GFSF2KEYABB General Electric Refrigerator - Instructions

as described, I used a thin screwdriver to wedge in and pull down existing, broken switch. I was able to pull it down about a 1/4 inch, but wasn't quit able to disegage it until I gripped it with pliers. I then pulled it out, unplugged the old switch, plugged in the new switch, and carefully tucked the wires back into the fridge and snapped the new switch into place.

10 minutes total.

Bing , Bang, Boom.

The original Ice maker water inlet valve proved to be good, I discovered that the water tube that delivers water to the ice maker was packed with ice. I remover the tube and ran hot water on it until it was ice free. Please check that tube before purcashing and installing any parts.

The repaire guy came in tooke it out and told me it is goin to coast $20 for the part and $50 for the labor..... So I looked, It was soooo eeezzz ALL you have to do is get the switch out( with help of my butter knife :) it plugs in to a little outlet on the wire (on the botom side) so take out the old one and plug in the new one wich I got for $8 + $6 shipping = $15 THANK YOU PART SELECT for saving me $55 Im a 36 y/o stayathome mom and Ihave never don this before, Im very proud of my self. well... it was very easy!

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

First I was told the compressor was bad. A quick YouTube lookup diagnosed it as 1 of 3 thing. Starter relay, motherboard, or compressor. First two are cheap, compressors are not. A rattle in the relay will tell you if it’s bad. Since there wasn’t I looked to the motherboard. A burnspot indicated it was the board that was bad. Partsselect had the cheapest board at the same quality. Fast delivery and I simply plugged in the ports to install. There was a small cover with some bolts to take off but nothing intricate. Plug and play and I was up and running. Great experience with the website and no previous experience with repairs of this type.

Replaced both temp sensors worked good for 2 days then began freezing food. Looked into it further on line. Found small motorized door broken that controls the cold air from the freezer

Remove rear plate. Remove fan bracket. Replace fan gaskets, blade and motor. Replace bracket. Replace rear plate. Very simple. Fixed the problem.

Your instructions were "spot on"! Pried out broken switch with screwdriver-reinstalled new switch. Very easy! Ordered on line on a Wednesday new part arrived on following Saturday-Great service and will definately use again. Highly recommend PartSelect!

We first watched https://www.youtube.com/watch?v=NgjfzdHrsak, the PartSelect repair video for this. It was helpful.
We were almost scared off by the first review on the PartSelect site, as it said the glass would not fit into the Crisper Cover Frame. Only later did we see that there was a second review lower on the page, which identified the error the first poster was making: There are two flat tabs, about 2 1/2 inches long and 1/2 inch wide, one above each crisper opening on the underside of the frame. The glass is intended to fit snugly into these retainers, and does not slip in unless you use a flat blade screw driver first, to lever them a little wider open. Then it can slip in. The glass does fit, albeit snugly.
The erroneous review says it is 1 of 1, so initially we didn't look lower. I suggest it be moved down the page, and labeled 1 of 2.
My husband helped, and I, the wife, did the actual repair. So this is something that depends on a little dexterity, and a little patience. That is all.
Melissa

Ordered the icemaker replacement. unplugged the unit, followed the simple instructions and got it done in less than 30 minutes. It did take a LONG time to start making ice. But it's working now.

Very easy. Just replaced drawers. Thank you for very quick service!

Replaced defrost thermostat along with temp sensor watched the video on this page simple fix

I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.

I visually inspected the compressor and narrowed down the source of the noise to the freezer area. Then I removed the doors and the screws securing the divider panel. Next I removed the bottom panel of the freezer, the styrofoam insullation panel and the evaporator motor. The motor is mounted between two grommets. I replaced the grommet facing the fan blades. The aluminum reflector below the styrofoam insulation panel had also come loose. I reattached it and reassembled the refrigerator in reverse order. The noise is gone!