GFD43ESSM0WW General Electric Dryer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Belt Was Broken
I watched the installtion video and actually did it faster than the video and yes you do have to be careful of sharp edges I did cut one finger. Other than that no problem I was all back together and using the dryer in less than 15 minutes
Parts Used:
-
john l from cumberland, RI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Sqeaking during operation
I used these two videos to help me clean the inside of the machine, then change the drive belt.
Parts Used:
-
Pete from San Dimas, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
My drum gasket needed to be replaced.
The repair was easy. First I took out 2 screws. Then I lifted off the top. Next I unscrewed 2 to take off front. I leaned off the front and reached in got out old gasket. Replacing new gasket went right around top front panel under the clips. Putting front on and returning 2 screws. Then Same for top. Dryer runs and sounds like new. Thank You for your quick mail and easy help?
Parts Used:
-
Ronald from Hollywood, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Drum wouldn't turn, snapped drive belt
Removing the top and then the front of the dryer went fairly easily after finding the screws. The drum came out with just a little coaxing, does not gets screwed in place. To me the trickiest maneuver was getting my hand under the drum to place the belt over motor pulley and around the tensioner pulley. You must look up an image of the belt routing. It took me forever to figure that out. If not for that, this in a half hr fix. Ps don't forget to unplug the dryer.
Parts Used:
-
Donald C. from Smithtown, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Lower Front Felt Drum Seal failed and was flapping inside the dryer drum
Your site offered a video tutorial that removed any anxiety about doing the repair correctly. Removed front of dryer, disconnected wire assembly going to the front, replaced seal in seconds, returned dryer to original set up. simple. luckily. very easy to use website.
Parts Used:
-
monte from clayton, NJ
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Replace light bulb in drum.
-
Scott from Pascagoula, MS
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Dryer door would no longer shut.
Simply popped the old broken part out and popped the new part into place. I wasn't sure if it was the Latch Door or the Door Strike. Once the parts arrived, it was clear the Door Strike was not the issue.
Parts Used:
-
Fawn from Loganville, GA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Drive belt for dryer frayed and making noise
Followed the online demonstration on the website when i ordered the part. The video was outstanding and easy to follow. I now have the confidence to make other minor appliance repairs.
Parts Used:
-
Vincent from NORTHVALE, NJ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
dryer door would not stay closed
-
Dave from Redondo Beach, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!