GDWT106V00WW General Electric Dishwasher - Instructions

It was an install. My problem is that the drain tube is not standard to other dishwashers,so I could not get it at either of the local home improvement centers. The good news is that it is larger than the standard, and offers better discharge.

I hand removed the snap in wheel axels and replaced the axles with new ones, by hand, no tools needed. On this dishwasher basket the wheeel axels just snap onto the metal cage "wires" of the roll out basket holding the dishes. Very simple. Used pliers to squeeze each old axle retaining nubs,from each of the eight wheels, , then just slipped (pulled the wheels off the axles) and discared only axles (that here the problem, detaching frequently from grasping the pull out dish basket, due to heat taking the temper out of their gripper (to basket).

Ordered on a Friday and parts arrived Sat. No tools required. Pieces easily slipped into place. Dishwasher is all fixed. This site is much easier to use than GE's. Will use PartSelect for all future replacement parts.

I inserted wheel axle into wheel and attached to bottom rack axle. It was simple. No problems.

I only had to repair the wheel axle. Since I read another post stating you don't have to change the wheels, I ordered only the axle and they popped right into the existing wheel and attached to bottom rack better than original design.

It was very simple to install. At first my husband thought I had ordered the wrong part. I guess they just revamped the part and it worked out really well. And I didn't have it mailed special but I got the parts in about 2 days. My only problem is that the shipping cost as much as the parts.
But the parts are installed and the wheels don't fall off anymore!! If I need anything else I will use your company again and I will tell friends and family about you guys.
Thanks

Only one axle was broken, but I replaced all 8 because GE had redesigned the axle to prevent future problems. Decided to just replace them all and be done with it. Took 10 minutes, start to finish and all is well.

snapped on wheels

The repair was very simple. I removed all eight wheels and discarded the old axles by pinching them out of each wheel and replacing them with the new (and improved) axles. I then turned the rack upside down and simply snapped the wheels back on the spindles. It took me longer to explain this than it took to make the repairs.

The replacement studs that were suggested fixed the problem that we were having. The fix was easy and took less than ten minutes to take the broken studs out and snap the new ones into place. The studs are designed to hold onto the rack much tighter than the original studs and completely fixed the problem of the wheels falling off anytime you tried to move the bottom rack.

I examined the wheels and noticed that they were actually fine, it was just the clip on axles that had worn out. I had recently used a dishwasher cleaner, I think that was the straw that broke the camels back. The replacement axles that I ordered were actually a bit different than the original. It turns out they had been greatly improved, so the new ones snapped easily into place by hand. The lower rack rolls perfectly, like new!

Very easy, saw the parts I needed online, ordered them, and installed them. Easier than I thought. Saved probably $200 in having a repair man come to the house. Outstanding results! Thank you!

old axles were removed by pulling wheel assembly from lower basket pins. squeezed old axle with needle nose pliers and discarded broken wheel axle. snapped wheels in place on new wheel axle and snapped wheel assembly into place on the basket. i replaced only two axles since the remaining ones were still intact. actual repair time was under three minutes. if all eight wheels would have to be replaced, i'm positive it would have taken no more than five to six minutes. in fact, the new wheel axle is a much better design than the original.

The repair was so simple a child could do it. It took less than five minutes and now the drawer rolls smoothly and is quite sturdy.

Very easy! Removed 4 screws that was holding the valve to the bracket. Placed bracket over water inlet line. Attached copper threaded coupling with pliers.Screwed valved on to the coupling. Attached bracket to the valve with 4 screws. Reattached water line. Attached bracket to frame of dishwaser. Put kickplate back on and done!