Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
GDT655SSJ0SS General Electric Dishwasher - Overview
Save your modelModel Saved!
Save your model for later to make things easier.
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This lower rack roller is a genuine replacement component designed to support the smooth and stable movement of the dishwasher’s bottom rack. Measuring approximately 1.5 inches in diameter and finishe...
Please be informed that this OEM-verified part that DOES NOT come with the heatshield, as per GE directly and are no longer required. This lower spray arm assembly is an essential component of your di...
This dishwasher door latch is designed to secure the door during operation by connecting to the door strike and ensuring a tight seal. Mounted to the tub frame, it plays a critical role in enabling th...
The element heating assembly is found at the bottom of the dishwasher tub, and helps to warm the water in the wash cycle, and dry the dishes afterward. If the water does not heat up during the wash cy...
- Includes: 4 brackets, 4 roller wheel brackets, and 8 wheels part # WD12X26146
Dishwasher Lower Dishrack Carrier and Roller Kit (Set of 4). This kit will replace all four one piece roller carriers w...
This is a washer inlet valve assembly for your dishwasher. This valve allows water to flow into your dishwasher at the proper rate. If your dishwasher tub is not filling with water or filling when the...
This mounting bracket is manufactured to secure your dishwasher to your countertop. Mounting brackets should be installed so the dishwasher doesn’t tip forward. You can fit the bracket to either the c...
This dishwasher drain pump kit is designed to efficiently remove water from the tub during the drain phase of the wash cycle. It plays a critical role in maintaining proper drainage and preventing wat...
This OEM mid spray or center wash arm assembly distributes water and detergent in your dishwasher during the wash cycle. It has small nozzles that spray water onto your dishes and is located between t...
This OEM-compatible screw is designed for use with many GE dishwashers. Measuring 8-16 HXW and 1/2" in length, this stainless steel screw secures the middle spray arm hub to the upper rack assembly, e...
This is the user interface control board for various dishwashers. The user interface panel is what you directly interact with on your dishwasher to start and stop it and select the specific cycle you ...
This detergent dispenser is designed for use in dishwashers and serves as a secure compartment for holding and releasing detergent during the wash cycle. The dispenser opens at the appropriate time to...
$48.43
In Stock
Order now and your part arrives by Apr 23
Questions And Answers for GDT655SSJ0SS
Ask our experts a question about this model and we'll get back to you as soon as possible!
15 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Matt
December 14, 2019
When I push start it beeps several times and light on front blinks
For model number GDT655SSJ0SS
Hi Matt, beeping sounds may indicate a problem with the dishwasher caused by power surges. To correct the problem, try pressing the "Start/Reset" pad to reset the dishwasher. If the problem persists, reset (reboot) the control by turning off the circuit breaker supplying the dishwasher for 30 seconds. Turn the circuit breaker back on and the dishwasher should function normally. Thank you for your question and good luck with your repair!
6 people found this helpful.
Did this question help you?
Thank you for voting!
Gary
February 9, 2020
I have no power to the user control panel. I have power to the main control panel. Do i need to simply replace the user control panel or could this be another issue?
For model number GDT655SSJ0SS
Hello and thank you for writing.
We suggest to try a hard reset:
Go to your breaker box and shut the breakers for your unit off, wait 5 minutes and then turn the breaker to on again. That should hopefully clear this problem.
If this does not fix this problem then your door latch PS6447681 and strike PS8690622 might be faulty and possibly needs to be replaced. This is more likely than a faulty control panel PS12342776, you should check the part(s) for signs of damage or test with a multimeter, and replace the part(s) as needed. We hope this helps. Please contact us anytime if you require further assistance.
We hope this helps. Please contact us anytime.
Assuming I have a bad door latch. Using a multimeter how can I test the latch to ensure this is the issue. I have no power to the user control panel. I do have power to the main control panel, a solid indicator light. I have attempted to reset by turning off the breaker for 5 minutes. I would like to confirm/rule out the door latch prior to moving to the user control panel.
For model number GDT655SSJ0SS
Hello Gary, Thank you for the question. With the power disconnected from the appliance, the latch can be tested from the main control at connector J711. The wires would need to be disconnected and tested from pin 3 (tan and red wire) to pin 4 (violet and yellow wire), then from pin 3 to pin 5 (white and silver wire) for continuity. When the door is closed, there should be continuity shown for both tests. If there is not continuity, then the latch would need to be tested directly in the same manner. We hope this helps.
Hello, I have seen "dishwasher beeping with orange light on and not starting" under Q&A. I have changed the latch on the tub side. Did not help. Thinking that it could be the control board. But, do I need to change the harnesses? Which ones? Can you assist? Thank you.
For model number GDT655SSJ0SS
Hello Jay, thank you for reaching out to PartSelect. Based on the description that you have provided, if the problem persists even after replacing the door latch, we would recommend checking the user interface board, part number PS16762500, to fix the issue. You can switch the wire harness from the old UI control board to the new board. We hope this solves your problem!
Dishwasher has no power. Motherboard replaced by repair man. He had to come back to hit reset behind kick plate. Dead again. Can’t find reset button. Where is it located behind kickplate
For model number GDT655SSJ0SS
Hello Marcia, thank you for asking. If your GE model has a kickplate, you can unthread the screws to remove the access panel, and you may find two buttons in the bottom left corner. Pressing the first button will reset your GE dishwasher. Or, you may try turning off the circuit breaker supplying the dishwasher for 30 seconds, and turn the circuit breaker back on. We hope one of these will help.
Did this question help you?
Thank you for voting!
< Prev
1
2
3
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
I first tested for 120volts to my dishwasher to verify it was getting power from my electrical panel. Then tested pins 2 and 5 on the control board to make sure there was 14 volts going to the user interface harness. After I verified that I knew it was the user interface that was bad. I watched a video I found on YouTube and followed it.
... Read moreThis repair was fairly easy while watching the video and making sure that you use the correct pin out that comes in the box for your model. I’m not an appliance repair person and it took me about an hour start to finish. I’m going to attach the video I https://youtu.be/TI8cUjy5YOE
Didn't actually do the compete repair but got close. Pulled out dishwasher, disconnected and checked continuity on the existing heating element (about 16 ohms) the new element was also about 16 ohms. This indicates they both were working fine and no need for replacement. Next step would have been to swap the elements would have been
... Read moresimple. Tried to replace main board as well, still not the issue so giving up and replacing the dishwasher. It wasn't the high temp cut off thermostat either incidentally and no error codes in maintenance mode. Check continuity of your existing element before ordering to save aggravation.
Open the washer, remove the bottom dish rack, then twist off the bottom water sprayer. Use a screwdriver to remove the mounting/ stabilizing screws so you can slide out the dishwasher. Close the dishwasher and slide it out. Underneath at the back there are two wires powering the drying element, carefully remove them. Use an adjustable wre
... Read morench to remove the two plastic mounting nuts for the drying element. Open the washer and remove the old drying element, and insert the new element. Reassemble the dishwasher in the reverse order if disassembly.
