This is a lower rack roller for your dishwasher. It attaches in the lower roller assembly on the bottom of your rack to allow the rack to smoothly slide in and out. This replacement part is 1.5 inches...
$13.15
In Stock
Order within the next 3 hrs and your part ships today!
This part is a replacement gasket for your dishwasher. The gasket creates a seal at the bottom of the dishwasher tub, so water does not leak out while the dishwasher is running. If you notice water le...
$8.56
In Stock
Order within the next 3 hrs and your part ships today!
This is replacement door latch for your dishwasher. The door latch is attached to the tub frame, and connects to the door strike to keep your dishwasher door closed during operation. If you have a bro...
$44.31
In Stock
Order within the next 3 hrs and your part ships today!
Note: This "Service Rack" fits numerous models. Per factory, on some models, it may be necessary to move the silverware basket to the inside of the rack along the right side.
$90.13
In Stock
Order within the next 3 hrs and your part ships today!
The tub gasket, also known as the door gasket runs along the perimeter of your dishwasher basin and creates a seal that prevents water from leaking out when the tub is full. If you notice water on the...
$21.63
In Stock
Order within the next 3 hrs and your part ships today!
This lower spray arm assembly in your dishwasher distributes water and detergent during the washing cycle by spinning around and spraying water in different directions. You can usually find it attache...
$19.76
In Stock
Order within the next 3 hrs and your part ships today!
This is an end cap for a dishwasher rack. This part is about 2.5 inches long, is black, and is made of plastic. You may need to replaced this part if it is broken, or if your dishwasher rack continuou...
$14.31
In Stock
Order within the next 3 hrs and your part ships today!
This mounting bracket is manufactured to secure your dishwasher to your countertop. Mounting brackets should be installed so the dishwasher doesn’t tip forward. You can fit the bracket to either the c...
$7.50
In Stock
Order within the next 3 hrs and your part ships today!
This is a washer inlet valve assembly for your dishwasher. This valve allows water to flow into your dishwasher at the proper rate. If your dishwasher tub is not filling with water or filling when the...
$32.48
In Stock
Order within the next 3 hrs and your part ships today!
The detergent dispenser in your dishwasher stores the detergent until it is ready to be dispensed. If your dishes are not coming clean, or you notice the detergent is still in the dispenser at the end...
$38.21
In Stock
Order within the next 3 hrs and your part ships today!
This OEM mid spray or center wash arm assembly distributes water and detergent in your dishwasher during the wash cycle. It has small nozzles that spray water onto your dishes and is located between t...
$16.91
In Stock
Order within the next 3 hrs and your part ships today!
Questions And Answers for GDT630PSM0SS
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Dale
February 28, 2023
My dish washer won't start when I press the start button all the lights come on and stays that way
For model number GDT630PSM0SS
Hi Dale, thank you for your inquiry. According to our research, the most probable cause of this issue may be a faulty door latch, part number PS6447681, which ensures that the dishwasher door latch is shut. If the door does not latch properly, the door switch might prevent the dishwasher from running. If the door latch is broken, you may need to replace it. If there is no issue with the door latch, then you may need to check the drain pump, part number PS12582714, as a faulty drain pump unable to drain any water could prevent the dishwasher from starting. If the problem persists, you may need to check the electronic control board, part number PS16226072, as a faulty board may be unable to supply power to the electrical components. We hope this information helps!
Washer won’t start. Made short grind noise then wouldn’t drain. Now shows FTD in screen. What does that mean?
For model number GDT630PSM0SS
Hello Todd, thank you for contacting us. The FTD code stands for "Failure to Drain" and indicates that your dishwasher is unable to perform one of its primary functions, which is to drain wastewater. Make sure the drain hose is not clogged or broken, and is placed properly. If that is good, then the issue seems to be with the drain pump and you may need to replace it, the part number is PS12582714. We hope this solves your problem!
Took off the kickplate, diconnected the wires and removed the whole door by lifting straight up, removing spring wires from hinges. Once door is disconnected from the machine, removed one hinge by removing bolt. Slid gasket into place, secured hinge back in place, then reconnected wires at bottom, replaced hinge spring wires and slid d
... Read moreoor back down onto hinges. Now that we know how to do it, could do it in 15 min to half hour.
1. Turn off breaker supplying power to dishwasher in electrical panel 2. Open dishwasher door 3. Unscrew the screws that secure the dishwasher to the counter. 4. Tip dishwasher forward. Identify the non-functioning door latch. It looks exactly like the replacement. Unclip the wire harness from the door latch. 5.
... Read more On the inside of the dishwasher, there are 2 screws directly under the door latch. Unscrew them and carefully set aside. 6. Remove old door latch. 7. Set new door latch in place. Holding securely, replace screws removed in step 5. Toward the end they get a little tougher to screw in. 8. Plug wire harness into new door latch. 9. Re-align dishwasher and re-secure to counter in previous position. 10. Test latch to make sure it closes properly. 11. Turn on breaker in electrical panel. The dishwasher should now function properly.
This didn't work out well. At the beginning of September the control panel in the door started to work erratically, the lighted buttons did not light up as expected. I ordered a replacement board and installed it. CONFIGURED UI SERVICE CONTROL Part #: PS16618944 This did not help, so I ordered another control board and installed
... Read more it. CONFIGURED SERVICE MACHINE CONTROL BOARD Part #: PS16226072. This did not help. This control board has a small orange fuse that looks like an old fashioned transistor. it was fine, as was the fuse on the previous control board. There were two things about the Control boards that might help someone figure out what went wrong. When I took out the original control board, there was evidence of component overheating. When I installed the new control board there was a green light that was blinking. I had hoped to complete this repair, but we have been without a dishwasher for over a month, so I bought a new one. (I am a competent Instrumentation and Controls technician) It could be that there is a bigger issue here; a major component failure. If anyone has some suggestions to try, I would like to repair the machine and sell it as a used appliance.