This is a lower rack roller for your dishwasher. It attaches in the lower roller assembly on the bottom of your rack to allow the rack to smoothly slide in and out. This replacement part is 1.5 inches...
$13.15
In Stock
Order within the next 7 hrs and your part ships today!
This part is a replacement gasket for your dishwasher. The gasket creates a seal at the bottom of the dishwasher tub, so water does not leak out while the dishwasher is running. If you notice water le...
$8.56
In Stock
Order within the next 7 hrs and your part ships today!
This is replacement door latch for your dishwasher. The door latch is attached to the tub frame, and connects to the door strike to keep your dishwasher door closed during operation. If you have a bro...
$44.31
In Stock
Order within the next 7 hrs and your part ships today!
Note: This "Service Rack" fits numerous models. Per factory, on some models, it may be necessary to move the silverware basket to the inside of the rack along the right side.
$90.13
In Stock
Order within the next 7 hrs and your part ships today!
The tub gasket, also known as the door gasket runs along the perimeter of your dishwasher basin and creates a seal that prevents water from leaking out when the tub is full. If you notice water on the...
$21.63
In Stock
Order within the next 7 hrs and your part ships today!
This is an end cap for a dishwasher rack. This part is about 2.5 inches long, is black, and is made of plastic. You may need to replaced this part if it is broken, or if your dishwasher rack continuou...
$14.31
In Stock
Order within the next 7 hrs and your part ships today!
This mounting bracket is manufactured to secure your dishwasher to your countertop. Mounting brackets should be installed so the dishwasher doesn’t tip forward. You can fit the bracket to either the c...
$7.50
In Stock
Order within the next 7 hrs and your part ships today!
This is a washer inlet valve assembly for your dishwasher. This valve allows water to flow into your dishwasher at the proper rate. If your dishwasher tub is not filling with water or filling when the...
$32.48
In Stock
Order within the next 7 hrs and your part ships today!
The detergent dispenser in your dishwasher stores the detergent until it is ready to be dispensed. If your dishes are not coming clean, or you notice the detergent is still in the dispenser at the end...
$38.21
In Stock
Order within the next 7 hrs and your part ships today!
This part is the replacement carrier roller for your dishwasher. It is also known as the wheel support. It is made of gray plastic and is approximately 5 inches by 2 inches. The carrier roller support...
$14.74
In Stock
Order within the next 7 hrs and your part ships today!
Questions And Answers for GDT605PSM0SS
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
3 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
James
January 21, 2023
Circuit board won’t show power, but power is good to it
For model number GDT605PSM0SS
Hello James, thank you for your question. It may be that there is a blown Control Board Fuse, part number PS12743197. We are pleased to have been able to help.
Control panel just beeps and lights up all the time. Unplugged it / stopped for awhile but then started again.
For model number GDT605PSM0SS
Hello Kristie, thank you for your inquiry. According to our research, we would recommend checking the wire harness of the user interface board and the control board. If the issue persists, you may need to replace the configured user interface control board, part number PS16762502. Glad to be of help!
Do you carry the CONFIGURED USER INTERFACE BOARD for dishwasher,
GE GDT605PSM0SS?
Please direct me to buy it because it doesn't shown anywhere and I really need it.
Thanks!
For model number GDT605PSM0SS
Hi Gamal, thank you for contacting us. The user interface control board, part number PS16762502, will fit your model. We hope this is helpful!
Took off the kickplate, diconnected the wires and removed the whole door by lifting straight up, removing spring wires from hinges. Once door is disconnected from the machine, removed one hinge by removing bolt. Slid gasket into place, secured hinge back in place, then reconnected wires at bottom, replaced hinge spring wires and slid d
... Read moreoor back down onto hinges. Now that we know how to do it, could do it in 15 min to half hour.
1. Turn off breaker supplying power to dishwasher in electrical panel 2. Open dishwasher door 3. Unscrew the screws that secure the dishwasher to the counter. 4. Tip dishwasher forward. Identify the non-functioning door latch. It looks exactly like the replacement. Unclip the wire harness from the door latch. 5.
... Read more On the inside of the dishwasher, there are 2 screws directly under the door latch. Unscrew them and carefully set aside. 6. Remove old door latch. 7. Set new door latch in place. Holding securely, replace screws removed in step 5. Toward the end they get a little tougher to screw in. 8. Plug wire harness into new door latch. 9. Re-align dishwasher and re-secure to counter in previous position. 10. Test latch to make sure it closes properly. 11. Turn on breaker in electrical panel. The dishwasher should now function properly.
This didn't work out well. At the beginning of September the control panel in the door started to work erratically, the lighted buttons did not light up as expected. I ordered a replacement board and installed it. CONFIGURED UI SERVICE CONTROL Part #: PS16618944 This did not help, so I ordered another control board and installed
... Read more it. CONFIGURED SERVICE MACHINE CONTROL BOARD Part #: PS16226072. This did not help. This control board has a small orange fuse that looks like an old fashioned transistor. it was fine, as was the fuse on the previous control board. There were two things about the Control boards that might help someone figure out what went wrong. When I took out the original control board, there was evidence of component overheating. When I installed the new control board there was a green light that was blinking. I had hoped to complete this repair, but we have been without a dishwasher for over a month, so I bought a new one. (I am a competent Instrumentation and Controls technician) It could be that there is a bigger issue here; a major component failure. If anyone has some suggestions to try, I would like to repair the machine and sell it as a used appliance.
