GDP6880XLP0 Whirlpool Dishwasher - Instructions

Installed pump kit. Was surprised the kit seemed different( some parts changed or deleted. Instructed to discard old parts and follow with new configuration. Reassembled and tried t fin it works fine now. Thank you so much

This is the second time I have replaced a rack. You just pop on the new rollers and you're good to go!

Actually I ordered the drain and wash impeller kit because it was listed as the #1 cause of failure to drain. I then hired a plumber to install it. He did so and that didn't solve the problem. So I was about to buy a new dishwasher. I then noticed that the second most frequent cause was a problem with the "dishwasher drain check valve." I watched the "partselect" video on how to change that. I didn't have a new one but I thought I would take out the part and see what I could learn. As it turned out it was blocked by a little piece of what appeared to be a walnut chip. I cleaned it out reinstalled the drain check valve and the problem was solved.

I layed the bottom rack upside down on the counter. Removed the old wheel sets and the new ones just snapped into position. I think the rack rolls better now than it ever did with the original equipment. I'm glad we purchase the Tandem Rack Rollers instead of a new dishwasher, it works great.

Took old one off , installed new one!!

We took the rollers off the old one (new ones came with the dishrack also) and put them on the dishrack (they snapped on). There was also an extra piece that we figured out how to put on. Then slid it in place and it was fine.

Removed the washer from the cabinet, although the repair kit could have been replaced without this step. However, it still made it easier. Removed the spray arm assembly and the top cover to the motor. I had to block the motor to keep it from turning while I unscrewed part number 11. The rest was very self explanatory. The "impeller" was seized onto the motor shaft (20 years old) so I had to use a chisel to break what remained off, then clean some corrosion from the shaft. The repair kit worked and the pictorial parts diagram that came with the kit was very clear. Bottom line: "Easy peasy, lemon squeezy!" Great web site for diagnosis and parts diagrams!

The old spring on the detergent dispenser box door failed and the dispenser door would not pop open at the right time in the wash cycle.

Ordering the new spring was easy on the website. Need dishwasher model number, stock number and serial number.

Hint - Order at least 2 springs! They are not expensive.

I followed the instructions in the video. I could get the spring on the spindle correctly but could not get the two spring prongs to catch to create spring tension on the door without using a thin knife blade to carefully push each prong to where it caught on the dispenser door.

I needed to slide the prongs slowly and carefully to get them to catch on the door. This distorted the spring. That's why you really need two springs. I then used needle nose pliers to pull the latching part of the spring to catch on the inner door. That distorts the spring, too.

So you really need two springs. One spring to learn how to do it and a second one to replace the one you distorted as you learned.

Take care

Unsnapped old rollers and snapped new rollers in their place. Very easy. The new set fit perfectly.

removed the bottom panel 4 screws,then replaced the new springs. I bought two and left the other one inside the panel saved $80.00 servive call.

I have a new faucet so I remove the screen then I used an extender ring put on your adapter an got the washer to run.

First, I checked the ripped box for damage to the dishrack. Fortunately, there was none. Then I looked for the instruction booklet. Unfortunately, there was none. And the parts bag was ripped and I did not know what was supposed to be in it. So, I rechecked the photo of the dishrack on the website and found that either parts were missing or the dishrack was different than illistrated. After a few moments of thought, I realized the latter was the case. I then figured I would have to use some deep thought to do the installation since neither the missing instruction booklet nor the unzoomable photo would help. So, I pulled out the tall thin thingamabob from the old dishrack and put it in the new one though it did not secure as tightly. Then I put the wheel units on just like the old one. What I could not immediately figure out was where the collapsible rack row was mounted. I eventually realized that the rod went into a hole in the wheel units and the latch mounted above one unit. I still have no idea where the two other tan clips go. Though the dishrack is different and thus requires different science to fill it, it appears to do the job.

Thanks for asking.

By the way, it was not blue.

I bought the kit because it had other parts that I thought I needed.

Purchased and installed new faucet attachment. It arrived quickly and very easy to attach. Thank you !

Simply snapped new spray arm in place. Took longer to get the soray arm out of the shipping package.