GDF645SSN0SS General Electric Dishwasher - Instructions

just bolted on the new one and hooked up the hose

Pretty easy repair for this model dishwasher…
1. Turn breaker for dishwasher off.
2. Remove front lower kickplate.
3. Remove small wire connector from dishwasher door to control board connector on lower right side.
4. remove one screw to remove power wiring junction box cover on lower right side.
5. Remove wire nuts securing dishwasher power wires to incoming power leads.
6. Remove 2 screws holding junction box to dishwasher frame and move out of the way of the plastic control board shroud.
7. Remove screws holding control board shroud and lower control board.
8. Disconnect 3 electrical connectors from board.
9. Remove screw holding control board to shroud.
10. Install new control board into shroud in same orientation, reinstall electrical connectors, reinstall board/shroud assembly, reinstall junction box, reconnect power wires with wire nuts and electrical tape as required, install junction box cover, reconnect door connector to board, reinstall kickplate, turn circuit breaker back on.

Took it out of the box and set rollers on track
rolled in place ALL DONE

Unplugged power.
Shut off water supply.
Remove the kick panel.
Unscrewed dishwasher from under cabinet and side screws. lower feet to reduce tension.
As you slide the dishwasher out, be sure all lines (Drain, water supply, electric are free to move with dishwasher.
I was able to hold the dishwasher at an angle to easily get to the valve. After removing the the valve, i screwed the new valve back into place. I removed the Line between the valve and Dishwasher. Putting the line on the new valve. I removed the water supply line from the old valve and installed it on the new valve.
Placed the dishwater back in place and screed it back in. I ran the cycles. everything works!
I replace the kickpaner a couple of hours later. Check to make sure there were now leaks.

Nightmare!!! The Striker latch did not pop out with a screwdriver as it was supposed to. The whole dishwasher needs to be disconnected and pulled out, then front door removed and totally disassembled to remove the screw to replace the striker latch. lots of work to replace a striker latch. Bad design!

the design of this part is easy to break when closing the top rack.

there is a hub that clicks in place and a spinner within this that makes the water spray evenly on the top of the tub of the dishwasher

the part broke when closing the rack [a dish too tall hit it]

it took less than 5 minutes to replace as the part just clicks into two edge spots i did this without removing the rack or even looking into the tub all by feel

Simply pick the basket up to slide wheels onto axles and push in until they lock in place.

Twist counter clockwise to remove clockwise to install

My son did the repair, I ordered both latch and striker, only needed the latch...only took him a few minutes to remove the old and install the new and works just fine

-Disabled power.
-1/4” nut driver to take off kickplate.
-Unplug wires harness to door
-Dismount dishwasher from cabinets and pull out 4-6 inches
-uncouple spring pulley from door hinges.
-Open dishwasher door about 4 inches and pull out and up to remove
-Lay door down and remove 4 -T20 star bolts and two 1/4” bolts from door hinges(the door hinge has four bolts, but only remove one from each hinge that connects to the inner plastic door)
-remove vent cap and push up on interior plastic door casing to separate outer and inner door.
-Unbolt the soap dispenser module via 1/4” bolts and replace with new module. (be sure to line up module and gasket properly, installing 1/4inch bolts crossways, slowly tightening each bolt for a perfect seal).
-Reassemble the inner/outer doors and reattach to dishwasher in reverse order.
Be sure to plug the doors electric harness and kickplate.
-Plug the dishwasher back in and run it through a test.

I recently replaced the user interface, which took about 30 minutes. A week later replaced the soap dispenser module, which took 20 minutes. Disassembling the door was easier the second round.

I would read this project very easy for somebody with technical skills and easy with no prior skills

Took cover of door off. Removeddoor from frame 1st. Lift door off of hinge. Disconnect door from springs. Unscrew bottom screws at base of door. Lift front cover(actually slides down) remove old part replace with new.make sure unplug door from main body.

Replaced motherboard, parts select,very helpful in helping diagnose problem! Exchanged parts, credit account after returned parts. Great customer service All good stuff! They brought their A game for this diy-er...

1. Turned off circuit breaker
2. Pulled out dishwasher
3. Disconnected switch and popped out switch
3. Popped in new switch and connected
4. Pushed dishwasher back into place
5. Turned on circuit breaker
6. Turned on dishwasher and it worked

Repair was straightforward. You can change water inlet on this model from underneath in bottom from, although it is a little tight

Very straight forward. After removing the power source the dishwasher was pulled forward enough to access the the door hinge springs. Then the door could be removed and the inner skin separated to access the the dispenser mounting screws.