GDF570SSJ2SS General Electric Dishwasher - Instructions

Simply unscrewed the old damaged arm and screwed the new one on, took less than a minute

Removed two latch screws and one electrical connection, Removed
two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....

It took longer to uninstall and reinstall the dishwasher than it did to change out the part

Looked up the replacement part on YouTube, watched a video and followed the instructions. Part ordered was the correct part and the video showed how to access for replacing. Watched a different video for hooking up the disconnected springs that allow the door to lower and close smoothly. Whole process for repairs was less than 30 minutes.

Replaced latch

Not having to screw with the hose clamps is the advantage here!
Disconnect electric connection at motor.
Slightly bend tabs that hold the pump to motor, twist motor from volute.
Do this on old pump first to get a feel for how easy the tabs can be broken
Do same on the replacement pump, put new motor on, watch alignment
can be a bit tricky.

Pulled dishwasher out switch is on very bottom of pump housing, turned dishwasher on its back, took out 1/4" bolt holding on bottom of switch frame, took two very small screwdrivers and small picks to hold open switch clips, while switch was removed checked float for frew movement, put in new switch, removed screw drivers and picks checked to see all locked on new switch in position, replaced bottom plate and bolt, checked burner reset all good now dishwasher heats and drys!

Unhook water line . Turn off power to dishwasher. Remove dishwasher from under counter. Lay it on its back. Loosen clamps on drain pump and remove pump. Install new drain pump and tighten clamps. Be sure to put hanger in the hole on the pump. Very easy job. Reinstall water line and put dishwasher back under counter. Turn on power to dishwasher. Go to go.

After hours looking for problem. I tried cleaning door gasket. Did not stop leak. Looked at lower water spray arm and it was split. It is literally a 2 minute repair to remove and install. Knock on wood, no leaks in the last 10 washes.

took off 2 sheet metal on the bottom, lowered the dish washer, pulled it out enought to unscrew 2 screws, unplugged the old part plugged in the new, put it back together.
Works like a champ.

I replaced the User Control and Display Board and it is working very well now. The important things that should be noted are to take off the door and to open the door cover by unscrewing it. Those screws are located at the bottom of the door and two are hided inside.

Followed video instructions step by step.
I was fortunate i had enough slack in water, electric and discharge lines to avoid disconnecting.

Two wrinkles
1. wire clips on my door had to be pulled/pried loose from door and there were two not one

2. could not slide dishwasher out after lowering adjusters and figured out it was the mounting tabs bumpimng the granite countertop, thus the use of putty knives to slide the dishwasher out.

Super easy repair, just removed the old latch and replaced it with the new one.

The Mid Spray Arm Assembly was not spinning due to a dish that was in placed the dishwasher that was too high and hitting the arm. When it spun until it broke the center shaft. Replacement was easy. After removing power I pulled the upper tray out and removed the Conduit Mid Tiered Assembly by unsnapping it from the tray. I twisted off the broken spindle of the damaged arm assembly from the Conduit Mid Tiered Assembly and inserted the new arm and gently pushed it until it snapped into the Mid Tiered Assembly. Reinstalled the assembled parts by snapping into the tray making sure it was centered.

Well, I was about to go buy a new dishwasher but my wife convinced me to fix it. Ordered the part from PartSelect and I wasn’t sure of the part number but they knew exactly what I needed. The control board. Received the part quickly. Took about 30 minutes. The hardest part was finding the correct socket for the bolt in my tool chest. Super easy! Thank you!