GDF540HSD2SS General Electric Dishwasher - Instructions

Unscrew the upper and side holding screws. Move dishwasher part way out. I didn't need to disconnect the water or electric. Make sure the electricity is off. Remember your working around water. Take off the bottom plat removing two screws, Remove broken cable pulley and replace new. Buy two since your their you might want to replace both. Have fun! It's duck soup.

Popped the old one off. Popped the new one on. Easy as that.

I took out the old one and simply inserted the replacement. It was an exact replacement part and thus a perfect fit. Dishwasher is working fine now! Cost was around $40 (shipped) which I thought was reasonable.

Simply unscrewed the old damaged arm and screwed the new one on, took less than a minute

Removed two latch screws and one electrical connection, Removed
two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....

Looked up the replacement part on YouTube, watched a video and followed the instructions. Part ordered was the correct part and the video showed how to access for replacing. Watched a different video for hooking up the disconnected springs that allow the door to lower and close smoothly. Whole process for repairs was less than 30 minutes.

It took longer to uninstall and reinstall the dishwasher than it did to change out the part

Tub gasket was a piece of cake, remove/replace by push in. Bottom door gasket was PIA. First you need to remove the door. Then, since the old gasket is held in place with a plate that is riveted together, you must drill out the rivets. Then you can install the new gasket. But first, you must use tap to replace rivet with threaded screw - unless you can find teeny tiny rivets!

A quick twist of the locking nut

Very straight forward. After removing the power source the dishwasher was pulled forward enough to access the the door hinge springs. Then the door could be removed and the inner skin separated to access the the dispenser mounting screws.

Removed the top two screws that hold the dishwasher to the cabinet , remove the two screws on the bottom panel and remove the panel. Screw the levelers all of the way up and pull out the dishwasher about 6 to 8 inch. Hook the new cabe on the spring and pull around pulley and attach it to the door bracket. I replaced both cables. Reverse to complete.

Followed video instructions step by step.
I was fortunate i had enough slack in water, electric and discharge lines to avoid disconnecting.

Two wrinkles
1. wire clips on my door had to be pulled/pried loose from door and there were two not one

2. could not slide dishwasher out after lowering adjusters and figured out it was the mounting tabs bumpimng the granite countertop, thus the use of putty knives to slide the dishwasher out.

Watched YouTube video on how to diagnose problems. Once part was identified ordered from Partselect.com and replaced the user interface circuit board. Dishwasher is now working.

Followed troubleshooting procedure to determine that defective Flood Switch caused the problem and not the Heating Element. Replaced only the Flood Switch. I also replaced a deteriorated door gasket.

De-installed dishwasher from cabinet, removed door, and tipped unit over with back of tub resting on floor.

I followed the document referenced here for the troubleshooting and repair procedures: GE Appliances Technical Service Guide, 2012 GE Dishwasher, 31-9226.pdf available on web.

The pump went out after a few months of very loud noise during the drain cycle and then one day no drain or noise. A bit of research shows that this pump goes out frequently on this model so I ordered a new pump after inspecting the old pump for a clog or snag on the rotors.

The Install:
After removing the dishwasher from it's installed location and turning it on it's side (unplug water and electric of course), I was able to remove the pump from the two lines that connected it to the dishwasher and the drain line. I also had to unplug the pump from an electric connection to the dishwasher. Swapping out the new pump was the same but in reverse. Not a hard install, only simple tools required.

One note, my electric connection to the dish washer was different on this model pump since they changed the original part but there is an adapter included with this part so make sure it is in the box and fits before beginning.