GDF540HMF2ES General Electric Dishwasher - Instructions

Opened the door, put arm on bottom, slid in and twisted. Very, very easy. The right part means a lot. Thank you very much. “ Ol Stump”.

Dishwasher is under 2yrs old and suddenly failed to drain due to the drain pump not working. I read the reviews on how easy it was to change and went ahead and purchased one. After removing the screw from the appliance bracket under the counter and the two screws from the base plate, it was easy to pull the dishwasher from under the counter and away to flip to its side. I would recommend draining the drain hose first and making sure no water is in the tub. Keep a towel nearby. Removing the drain pump was simple. I needed a nose tip pliers to remove one of the hose clamps and a screwdriver for the other clamp. Once the pump was removed, I opened the old pump by twisting the top part while pressing the tabs to remove upper housing. There was a broken piece of glass that had wedged itself in the mechanism which prevented the pump from working. I wish I had checked that first, before purchasing a new drain pump. I kept the old pump as a backup for the future. It took no more than 20 minutes to get the pump replaced and the dishwasher back in place. Dishwasher drains just as new. By the way, costed under $100 with delivery. An appliance repair company wanted $250!!
Not the first time PartSelect saved me money and won’t be my last!

Removed toe kick. Removed door counter weights and placed door on soft surface. Removed two bolts(I was able to leave hinges in place) slid door panel down and off. Removed plastic snap fit cover and 4 bolts from UI board. Two of the stand-offs where broken, glued them back into place. Ensured jumpers were set to my model, snapped cover back in place and remounted door. The dishwasher now runs through the cycle and clean light but did not dry. That turned out to be a bad flood switch.

I checked all the drain lines and filter for blockage. All looked good. I unplugged the unit and unscrewed the two screws adhereing the dishwasker to the counter. I shopvacced the water out of the bottom of the unit, slid it out, and carefully placed it on its back to access the pump. I unplugged the power to the pump, removed the intake and outake ring fasteners. Carefully removed the pump and inserted the new part, mopping up water as I went. Replace the rings, plugged in power to the pump, righted the unit and put it back. Replaced filter with the one that came with the kit.

The lower tray was simple. Lifted the old one out and placed the new one on the lid of dishwasher.

Upper tray: Used the closed point of scissors to gently push the little piece of plastic on the slide and removed the cap on each slider. Pulled the damaged tray off of the sliders. Removed the piece that shoots the water onto the dishes and placed it on the new tray. Put the tray back on the sliders and replaced the little caps back onto the slider so that the tray did not come off of the track. Voila!!

The service lady looked up possible trouble items and narrowed it down to the flood switch. Being the most likely cause, I ordered a new one. I removed both trays, the lower sprayer, and both screens. The flood switch has an electric plug on the bottom of it that just pulls off. Just as with other appliance repairs, I actually got the old flood switch to work again before trying the new one. I should have tried to free up the float before ordering the new one. But in case this happens again, I’ll just put the new one in.

The replacement of the parts was simple enough, but the board appears to need a jumper which was not in the original board.

The start button works, but beeps three times and doesn’t start the washer

Turned off pier at breaker. Removed dishwasher from under counter after disconnecting water line from dishwasher and drain tube from under sink. You might get a little residual water but not much. Removed old flood switch took about 2 minutes. Replaced with new flood switch. Then tilted dishwasher back to get to plastic nuts that hold down heating element. Set unit back down and removed old heating element then replace it with new one. Replace plastic nuts that hold element. Exact parts makes job easy. Them put water hose back on an put washer back in place hooked drain hose back up. Turned water and power back on. Tested unit worked perfectly. Hardest part of job was putting the dishwasher back into counter and getting the Instalation back on top.
Parts replacement time was about 10 minutes.
Disconnecting and reconnecting and replacing dishwasher 40 minutes. But I wouldn’t pay anyone to do this because it’s really not difficult.

took out old and replaced with new

Had to remove the rubber gasket on the new spray arm to install the device, as it was hard to push into the above slot that fits the arm..

It was relatively easy to fix. I unscrewed the mounting screws from the cabinet, slide the dishwasher out to access the pump under the dishwasher, I did raise the dishwasher on the left side and steadied with a stool to make access to the pump fitting easier. Then I loosed both clamps at the ends of the hose ie. from the dishwasher pump and the connection to the sink drain line, pulled the clamp off of the end that connects to the pump and placed it on the new hose connection, I removed the old hose, connected the new one and tightened the drain line connections. I placed the hose in the hose holders on the side of the dishwasher slid the dishwasher back into place and secured it in place with the mounting screws.

Unplugged power.
Shut off water supply.
Remove the kick panel.
Unscrewed dishwasher from under cabinet and side screws. lower feet to reduce tension.
As you slide the dishwasher out, be sure all lines (Drain, water supply, electric are free to move with dishwasher.
I was able to hold the dishwasher at an angle to easily get to the valve. After removing the the valve, i screwed the new valve back into place. I removed the Line between the valve and Dishwasher. Putting the line on the new valve. I removed the water supply line from the old valve and installed it on the new valve.
Placed the dishwater back in place and screed it back in. I ran the cycles. everything works!
I replace the kickpaner a couple of hours later. Check to make sure there were now leaks.

Simply put it on and twist it to lock in place. Took all of 3 seconds

Simple! I removed the flatware tray and pulled out the old rack assembly. Rolled in the new one and replaced the tray. Not really a "repair" per se but a needed replacement.

Simply pick the basket up to slide wheels onto axles and push in until they lock in place.