GCWP1069CS LG - Instructions

After finding you on google it was easy to repair. It saved me $95.00 service charge. Your direction made it very easy.

I watched a video of how to replace the pump and it showed taking the top and front off to get to it. I actually found this could be done by removing the back panel from the washer. There were two hose clamps you have to squeeze and slide up and two wires going to the pump. There are three screws holding the pump that need to be removed from the front of the washer. Once these are removed all you have to do is push a tab down and the motor slide right out. The pump assembly can also be reached from the bottom of the washer.

Turn off hot water supply and activate a cycle on the washer momentarily, with hot water selected on front panel options to relieve hose pressure. Slide washer out to gain access to rear of unit. Unplug washer from AC source. Using pliers, remove washer supply hose from washer-side of the line (water may drain from hose) Remove single Phillips screw at bottom of each nylon lid holder at rear. Using a plastic putty knife, place between front panel and top lid to loosen lid and slide to rear. Remove lid and store aside. Hot and cold inlet valves sit side-by-side at top rear of the unit. Disconnect connector from valve by pulling gently away from valve plug prongs and place to the side. Using pliers, compress hose clamp and move to lower section of hose. Carefully rotate hose back and forth to remove from assembly. Inlet valve is held to washer body rear with 3 small Phillips screws. Remove first 2 and then while holding inlet valve body, remove final screw to free inlet valve assembly. Replace with new assembly by reversing these steps.Make certain when supply hose is reconnected, it is firmly tightened but DO NOT over tighten. Test washer by running a cycle to ensure there are no leaks.

Took off the old one and put the other one on. The only difficulty was that my husband has big hands and had a hard time getting to one end.

The bellows hose on the bottom of the tube had worn through where it flexed. This was an easy job except for the long reach you had to make under the washer to reach the hose clamps that held the part in place. These were spring loaded clamps which were easy to remove with pliers. I replaced them with ones that could be tightened with a socket wrench since it was hard to replace the sprung clamps.

Disconnect electric and remove top cover and remove connectors and hoses then the valves

This was very easy to instal. The aplaiance repair co. wanted $240 my LG is six years old and would rather buy a new one if I had to spend that much, so I gave it a shot and it took me 20 min to install the part. Told my wife she owed me $ 180 for my labor.

took out the drain pump and replace with a new one

During my troubleshooting, I removed the bottom to access the drain pump. I had to cut some wire ties so that I could make removing the wires easier. After checking the pump and putting everything back together, I determined that the pump itself was bad. Pump impeller should not rotate freely! After receiving new part, I installed it relatively easy. I didn't have to remove the bottom since there was enough room through the access hole. Just make sure to make where wires go before removing old part.

removed dryer which was stacked on top of dryer. opened washer top by removing screws from plastic hold down parts on rear. replaced valves with new valves you all sent me. reassembled and restacked dryer on washer

I received the part needed within a few days from ordering. I immediately removed the leaking part with the new part. It was a very simple install, and my washer is now leak free. If you think you cannot do these simple changes, think again, it's much easier then you may think. Remove the top cover of your washer machine by taking off the two screws in the back. Remove the hose clamp with a pair of pliers and pull off from the intake valve, of course make sure your water valve is shut off before starting. Remove the two prong clip. Using your pliers, disconnect the main hot water hose. Use a Phillips screwdriver to remove the two screws that holds the valve in place. Remove and discard it and replace with the new valve. Follow the steps and your done, it's that easy....TC

Followed the instructions that a fellow DIYer posted in PartSelect and a few I watched on Youtube. Pull out the detergent drawer, remove the back screws, slide the top off, unclip the control board, unplug Power & One more switch so that I could move it aside. Take the gasket retention wire off the door gasket & tuck it inside. Remove the screws in the bottom & top. Then slide the front panel, including the door up (not easy) and out. The part received was only the pump motor so I had to take a few pictures before so I knew I got it together right. Remove drain houses, pump screws, slide pump back and remove pump. A few more screws to remove the pump from the housing & replace with new pump. Put it all back together. It works! It only took about 45 minutes

UNPLUG WASHER.Unscrew 4 screws holding silver plate at back of unit. Remove plate to expose inside of unit. Locate drain hose at bottom of washer tub. Hose connects at front drain, bottom of tub, and at rear at the pressure sensor. Front and rear simply slide clamps down by grasping clamp tabs and sliding clamp off connection point. Disconnect from tub bottom by loosening main clamp with Phillips screwdriver and pulling downward. Have a towel handy as there will be water in the hose, and it will pour out when removing it from the unit. Installation is the reverse of removal. ATTACH THE HOSE ASSEMBLY TO THE DRUM FIRST, THEN FRONT, THEN LASTLY REAR. This order is the easiest way, otherwise you will spend extra minutes trying to get the tub connection to seat properly. Plug it back in (duh), then you're good to go for another 4 years or so until another hole wears in the hose. I have performed this repair on 3 different units, with 4 years being the average lifespan of this part.

We drained the water from the washer via the tiny hose/filter located at the lower left corner of the washing machine. The unit was then pulled away from the wall, unplugged and the hoses disconnected. At this time, we used the wet dry vacuum to suction the water that remained in the drain hose. We tilted the washing machine back until the front of the unit was 18 inches or so off the floor. We used the foot stool to hold the washer up in the air so that we could work on the pump. Replacing the pump was as easy as removing a few screws, unplugging the electrical connections and removing the faulty pump assembly from the plastic housing. (Be sure to mark what connector goes in what terminal). Re-assemble. Re-connect. You are ready to go. It took more time to ready the washer than it did to replace the part.

ordered part from Part Select and it was here very quickly,but the part came damaged (not the fault of Part Select). I ordered another one and PartSelect had it here the next day. I watched the video on how to replace it and it was very helpfull.The particular part I replaced (pump motor) does not seem very durable. I will buy an American made washer the next time I need one. I will use Partselect in the future and recomend it to others.