GCE24KBBAFWW General Electric Refrigerator - Instructions

We just pried off the fan blades and pushed on the new part. Could not have been easier. The rat has been permanently dipatched and, hopefully, that is that.

Used screw driver to lightly remove the old switch. Disconnected the 2 electrical leads to the old switch, then I connected those leads to the new switch. The light immediately came back on and I placed the switch into its housing hole and popped it in place. It works perfectly now. My wife said "let there be light"! Very easy installation. Thanks.

It couldn't be easier. Just pry out the old broken switch with a flat blade screwdriver. start at the bottom in case you scratch the door by accident. When the bottom is out - pull the switch out slowly and disconnect the two wires that are attached to the top, taking care to remember which color lead is connected to which wire. Then, take the new switch and connect the proper wires to their respective terminals and push the switch into the slot. Done!

snapped the old one out snapped the new one in.

i followed all the other submited solutions. really easy. popped out the broken light switch with thin tip screwdriver. careful not to let wires slip into compartment. then attached wires as i pulled them off broken switch. then carefully pop the new switch back in the slot. when i was younger i worked for an appliance repair company. i felt confident in this repair.

Ordered the part and within three working days the part was delivered. It took two minutes to pry off the broken part and one minute to snap in the new one.

replaced with new one

Unplugged the refrigerator first....then on the inside of the fridge, I popped the temp sensor cover off (upper LH side) and exposed the old sensor. I snipped off the old sensor about 3" down from the end and connected the new sensor (which I trimmed down to about 3" long) with some heat shrink wire nuts/connectors. Let the fridge run for a day or so and confirmed the problem was solved! Oh yeah, there was no way to tell the 2 wires apart (power vs. ground) on the sensor. However there was a manufacturer's stamp on the wires. So note the orientation of the text and mark one of the wires with a sharpie on both the old and new sensor before trimming. This will give you a reference for which wires to connect when adding the new sensor to the old wires.

It really was as simple as the other folks noted. Slid a screwdriver into the edge of the broken switch and it popped right out. Disconnected and reconnected each of the two wires and just slid the switch back into the slot. Truly a DIY fix.

Replaced light switch. Defrost cycle remains suspect but refrigerator has worked OK for about 10 days.

Things fall out of my refrigerator frequently thus the broken lite switch. Thought tape would solve until new part arrived. Thank goodness part came the next day as even with tape on and door close and light bulbs removed fridge read door as open and would not cool It is programmed not to run with door open. Within 24 hours part was delivered, unbelievable . It was that fast. Easy insertion and plugged in to the wiring and my refridge once more recognized the door was shut and began cooling. Thanks again

1. Removed and tested defrost heater, tests good. 2. Reinstalled defrost heater. 3. Removed and tested defrost over-temperature sensor, tests good. 4. Reinstalled over-temperature sensor using soldering iron, dielectric silicone grease, and heat-shrink tubing. 5. Removed the control printed circuit board and checked for blown fuse's, fuse's are all good. 6. Removed the defrost relay from the printed circuit board using soldering iron, bench tested the relay, it is good. 7. Soldered defrost relay back onto the circuit board, and reinstalled control board. 8. Removed and bench tested evaporator thermistor, the resistance is out of specification, ordered new thermister. 9. Installed new thermistor using soldering iron, dielectric silicone grease, and heat-shrink tubing. 10. Re-assembled refrigerator. 11. Installed temperature monitoring and recording instrumentation for 72 hour test. The defrost cycle is running correctly with a defrost termination temperature of around 90 deg-f. The defrost cycle ran twice while running the 72 hour test. 11. Removed test instrumentation and Put the unit back into service, The thermistor was the culprit. I bought the right part on the first shot, nice.

I ordered 3 temperature Sensors Part#PS304103 and viewed the video. Got there, opened the frig. and it looked totally different and no place in any part of this frig. that took these sensors as viewed on the video. Totally baffled why these parts were listed for this frig. there was no place in this frig that would access for these parts. Serial # was HR443071.Maybe this model is out of date for these parts. Trying to find someone who can repair it. Any ideas???Purchased this GE in 2008. Model #is GSS25WSTFSS Thanks, for your help. JIM

Had to remove all the covers and fans to expose the condenser, which was difficult as the parts were frozen to it. The styrofoam covering the condenser made it almost impossible to defrost it. Therefore, I ripped the styrofoam off to expose the condenser. Was not really difficult to fix the styrofoam cover using metal tape. Replaced temperature sensor in aluminum block, and used butyl sealant to secure. Had to also re-install parts of ice-ball kit that were not well covered. Lots of parts to keep track of, but anyone could do it.

I have a GE Profile French door refrig. It's only about 4 yrs old and the defroster stopped working. I read the other repair stories and was able to narrow it down to either the temp sensor, defrost timer, or main board. The refrig section was up to about 47 degrees and freezer was around 25. I could tell it was trying to cool but couldn't. So I tried the temp sensor first. I cut and spliced the new sensor on the outlet of the Evap. Coil and it took about 15 mins. Turned refrig back on and waited. The coil started to ice over after about 5 hrs I left the back panel off so I could see if and when then heater kicked on. After about 8 hrs I looked in and saw a faint glow and water trickling down and running out the drain. Turned out the sensor was bad and wasn't telling the main board it needed to defrost. I would try the sensor if you are having the same issues before spending a lot of money on the main board, defrost heater and or timer.