GC2227EEDW Admiral Refrigerator - Instructions

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

Thank you for the easy to install video. I do much better hands on repair than reading the instructions. It was supper easy and it works great. My 11 year old son said to me "WOW mom great job" since I did it myself! I will definitley use you again for any other parts I need.

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

This replacement glass shelf arrived the very next day-after it was shipped. I was so impressed with the easy method of ordering and the prompt delivery of this product-also, the quality of the shelf was perfect. Great service!! I would recommend this for everything-as far as parts needed for repair or replacement.

At first I thought I had ordered the wrong bracket but all I had to do was push it up and pull down and it snapped right in place. If a 71 year old lady can do this any body can do it. Thank you for the fast service.

Our Refirgerator had custome wood covering to match the cabinets. Be sure to take the covering off first. There are four screws on the left edge fram that need to be removed and two on top of the tpe edge frame. The panels then slide right off. Remove the spill tray and unscew the two screws at the bottom. Slide up the key pad and there are three screws behind the key pad that have to come out. There are two "plug in connections that have to be disconnected to lift the dispenser unit out. Take care not to damage or separate the connector wire from the keypad and the circuitboard.

The new solenoid and flapper assembly is different than the original. My guess is the orginal design was part of the problem and the redesign allows the solenoid to work better. I was suprised the new assembly did not come with a tension spring... SO be careful and DO NOT loose the tension spring from the old assembly. there are two screws that hold the olde solenoid in plae wonce you remove the flapper and tension spring. Put the new solenoid in, hold the tapper out and put the flapper assembly in. Rotate the flapper rod until you can seat the solenoid tapper. Replace the tension Spring and then reassemble as in reverse order.

We removed the old switch, unplugged it, plugged the new one in and it was easy to do. But when we tried to put the switch back in we had a very hard time doing it. Eventually got it in, but if it had not been for the difficulty we had getting the new switch to snap in to place, it would have taken under 5 minutes.

The round sealing door of the ice chute had to be replaced a alignment tab broke off the side.
1) unplugged the appliance from its receptacle.
2) removed catch tray at bottom of ice water depenser exposing two screws.
3) removed screws and slid cover up and away from keyed studs.
4) unplugged ribben cable from front panel.
5) removed additional screws and lifted the chute door and solenoid assemble.
6) replaced components and reassembled in reverse order.

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

We removed the old part, which actually looked quite functional. We put on the new part, thinking that the repair was not going to be effective, and that we were going to need other parts. But, the refrigerator is working perfectly now, and I have no more run-ons onto the floor. THank you very much.

Very simple fix, remove 3 screws, two connectors to the old switch

The repair went just as the short video showed. The paper instructions included with the part were not too good the photos were copies of copies from years ago with all the detail gone. But with the video on your website it was a snap for anyone with some mechanical skills.

I just follow the easy instructions on the video provided for the part in question. Easy to change and everything is working fine

First I removed the two screws to remove outside cover. Then removed three screws to the ice dispenser assembly. Slipped in the new round door assembly and replaced the removed screws. No problems.