GBS22HCPAWW General Electric Refrigerator - Instructions

I took the 3 screws off the cover that is in the back of the appliance, unpluged the plugs that attached to the circuit board pressed the 4 plastic pins that held the old board. Then I snapped the new board in place and pluged the plugs back into the new board. They will only go on one way so you cannot get the plug in the wrong place, job done appliance works fine. Thanks

Pull fridge out. Pull the little 6 by 12 silver plate off on the back middle bottom of fridge. Disconnect the quick connects . Remove from 4 plastic pins. Them reassemble.

Removed circuit board cover, unplugged l
Leads, rePlaced board, leads and cover. Done

Also watch the video. Super simple

I wouldn't have had a clue without your video. After the part was delivered, which was only in two days, I watched the video. The man explained everything perfectly, making our "fix" a breeze. It was great, I stood over my husband's shoulder, while he sat on the floor and told him what to do step by step. It couldn't have been easier. You guys are awesome!

Very simple fix by replacing the mother board. Your "how to" video made the repair even easier. The appliance repair estimate was over $400. I saved over $200. I already recommended your site to several other people. Thanks for making it so easy

Totally followed the instructions of the video that came with the sensor. Unplugged the the fridge, defrosted the freezer. Cut off the main sensor that usually is the one that goes out. Installed the the new sensor with new wire terminals, crimped them and covered with electrical tape. Fridge works like a charm. Partsselect is excellent. Saved me a few hundred dollars versus having a GE Tech come and do it.

Found out via searches that the most likely failed part was the Main Control Board. A simple repair with basic tools and a HUGE savings. Thanks to everyone here for the posts.

PS - on my particular GE model PFS22SISBSS there was no need to cut any wires as per the instructions because the wires did not exist on this unit.

The first and most important step was to diagnose the problem. To do this I found the Parts Select website and the part I thought was the problem. The previous repairs stories helped me to pin point the problem. The mother board came within a couple of days. All I had to do was take the back plate/guard off, unplug the connectors in the back, unclip the mother board and then do the reverse over again. The only problem was the ground wire. I had to take the one off that came with the part and switch it out with the old one, because it would not connect to my refrigerator. This was fairly simple and in about 30 min. I was done and had our refrigerator back. Luckily we had another in the garage as a back up so we didn't loose any food.

Thanks Parts Select

On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.

removed cover from rear of refrigerator. disconnect mother board connections. Unplug first, used needle nose pliers to squeeze plastic tabs holding on motherboard and replaced old with new and plugged back in connections. Plug back in refrigerator and done.

Easy

the new board was more complicated than the old, however the install instructions seem to have anticipated this. It works for mow. thanks for inquiring'

I easily removed the screws and then removed the board and took a picture so I would remember how to re-connect it. It was really easy and now my refrigerator is working great. If I can do it anyone can do it. My husband was amazed that I did it all by myself.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

very easy repair, simple exchange