FRSS2623AS7 Frigidaire Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
No problems
I had no problems. Screws arrived sooner than expected. It was a very simple installation. Very pleased with both the product and service.
Parts Used:
-
Nancy from LEHIGH ACRES, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Wrench (Adjustable)
2 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The new motor mount screw holes were not threaded.
I had to tap the screw holes with a 8/32 tap so that the screws would not bind.
Parts Used:
-
Greg from henrico, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Socket set
1 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bulb burned out
-
Jack from SILVER SPRING, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
15 of 53 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water Tube That Fills Ice Maker Leaking Water
Undone the water line that comes up the back of the refrigerator and pulled the water tube out the back of the refrigerator and reinstalled the new one and reinstalled the water line. Done
Parts Used:
-
PAT from BATON ROUGE, LA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
Installed a extra shelf
-
nathan from Buckley, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
I noticed ice on the inside of freezer door
The young lady that helped me was fantastic... great product knowledge and affermed the correct and we got it ordered... Fast shippers and the install was easy although there were no instructions to be had... checking the gasket and removing the old one,,, it pressed in place in moments... They are booked marked and will use them the next time...
Parts Used:
-
Russell from Lehigh Acres, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The gasket was torn.
The gasket arrived in two days as advertised. Removal was easy and did not require any tools. The new gasket was simply pushed into place. It was so simple and easy, I thought more was required. I will definitely use this vendor again !
Parts Used:
-
theodore l from jacksonville, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
old seals on both fridge doors
pulled the old seals off one at a time and starting from the top of each door, pressed the top edge of the seal into the groove, using the quik clamps to hold the top in palce at each top corner, went down each side of the door and pressed the seal into the groove, when I reached the bottom, I moved the clamps to the bottom and used thm to help press the seal into the bottom groove, Each door took about 15 min.
Parts Used:
-
Walter from Twinsburg, OH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
Ice Maker not getting any water
1). Shut off water supply to fridge. 2). Move fridge out to gain access to back of fridge. 3). Remove poly line to water tube have a glass handy to catch any remaining water that might be in line. Some may have a foam insulating washer around water tube remove it first. 4). My Sears-Kenmore was a twist lock water tube have to turn it to left or right depending on brand to remove tube. 5). After removing make sure tube didn't just have water frozen in tube ( that was my problem ) run it under hot water frozen piece will come out. 5). Problem fixed, reverse directions to re-install tube!
Parts Used:
-
Lawrence from Stow, OH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
Torn fresh food door gasket
Removed the old gasket and installed the new one. Really, really easy to do. Took me about ten minutes.
Parts Used:
-
Robert from Orlando, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
leaking water onto the evap fan freezing causing alot of noise
1st a changed the defrost stat. Waist of time. Realized there was no evaporator above fan. Noticed ice was builing up behind ice maker near fill tube. Found if I shut off ice maker ice wasnt building up on fan. Moved fridge out unplugged fridge unscrewed plastic nut. Turned 90 degrees. Replaced tube locked in place . Screwed nut back on . Plugged in and turned ice maker on. Wife happy ice was back on and no noise.
Parts Used:
-
Steve from Salem, NH
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
Original Seal was broken
Pulled out the old seal by hand. Cleaned the opening. Pressed the new seal in place. The entire process took about five minutes
Parts Used:
-
Thomas from Saranac, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Needed to replace split door seal
It took about 5 minutes to pull the old seal out and replace with the new one. Simple enough for a 71 year old woman to do alone.
Parts Used:
-
Maridell from Lexington, SC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!