FRSS2623AS5 Frigidaire Refrigerator - Instructions

Open freezer
Pry the switch out (bottom first, then push the tab on top while prying out)
Move wires to
New switch
Push switch in
Test

DID IT JUST LIKE THE VIDEO SHOWED. UNHOOKED ELECTRICS, CUT TUBING, HOOKED UP ELECTRICS THEN TUBES TO NEW PART. PIECE OF CAKE.

Removed shelves above the problem area. Tilted new shelf up to slide prongs into openings on one side, pushed in far enough to allow prongs on the other side to fit into their openings. Evened the shelf out then added some thick tape to both sides of the shelf to keep it from falling out.

The part i recieved, from parts select was a larger in circumfrence (<1/4) than the original. However i was not aware of this until after i treid to repair it.

I removed the broken fan from the condenser. This was very sipmle.

When i pluged the refridgerator back in to the outlet the fan tried to start up but soon began to make aloud noise, due to there not being enough clerance.

Consulted You Tube. Took off old gasket. Easy. Put on new one after getting it warm. The track on the new gasket did not sit properly. Took multiple attempts but finally worked. Size was perfect but the gasket color was different than original and therefore, different from the refrigerator door. No tools required.

I watched the video and followed every step as outlined. It worked perfect, until I reconnected the supply line to my triple water valve. I used the old compression fitting and the compression nut. I should have cut the line and installed a new fitting and nut. The water on the floor the next morning reminded me of that. So back out I went and replaced the compression fitting and it has been as good as new. The ice maker took a few cycles to work again, I think it needed to fill the line with water first. But I have a huge sense of pride every time I hear water dispenced or ice dump in the freezer. Thanks for the help and encouragement!

Straight forward repair. Remove the four screws holding cardboard back. Remove the 2 screws holding the valve. Unscrew the water lines and unplug the electrical connections. I would caution that it would be wise to either take a couple photos or write down the order of connection. Even though it is somewhat color coded and the water lines are different sizes, a photo removes any confusion. My old valve had threaded connections using brass nuts and ferrules. The new valve has push in connections so you need to cut the ferrules off.. When cutting off the tubing, be sure to cut square. An angled or "squished" cut will leak when pushed into the fitting. Attach the valve to the refrigerator with 2 screws and replace the cardboard back and you're finished. While you have the back off is a good time to clean the coils. I left my fridge out and back off for a couple of ice making cycles so I could check for leaks (how I know the tubing needs to be cut very square). All in all, a very easy fix.

very easy, make sure to watch the provided you tube video.

I looked at the internet before I purchased a new seal and saw how to repair it. It was a matter of pulling out the old seal and just popping in the new. The internet said to use a hair dryer to melt the rubber to adhere to the fridge in places where it wasn't. It was quick!

Write down where tubing goes, wiring is color coded.

Undo a few bolts unplug power and unhook water lines then recut all lines and push in to new value

The u tube instructions were exactly what is needed. I had to cut off the old plastic pipes. My pipe had threaded connectors. Pex push on connection is super easy. You don't really need a block of wood to cut it if you have a sharp utility blade. If if you are sure this is the problem this is a really easy fix. Steps 1 turn off water at wall unplug electric also 2. Disc line at valve on refrigerator 3. Remove 2 screws holding valve 4. Pull valve out and remove plastic hoses and electric connections pay attention to color of pipe and electric connection. Mine were color coded. Had to cut off thread connectors. Reattach in reverse order or do one at a time. Check for leaks.

I first ordered the wrong switch I called and got a return label and was refunded my money before even shipping the wrong switch I was helped for the right switch and it arrived in 5 days the replacement works perfectly very easy to install. Thank you

The part was easy to install and solved the problem! We had ice within hours. Thanks PartSelect!

carefully removed retainer from old valve