FRS26RLECS7 Frigidaire Refrigerator - Instructions

I just pulled the old gasket out , pressed the new one in with my thumb,and was finished. thank you, Langley

un plug fridge. removed ice maker from fridge. loosen 2 mounting screws. lift unit in slots to get over heads of screws. unplug wire harness. remove cover. remove 3 screws from control housing. remove 2 motor mounting screws. unplug motor wires from switches w/needle nose. installation is the reverse. plug in fridge turn on icemaker. takes 10 to 15 min to start to cycle.
easy and cheaper than new fridge or ice maker

Took off old gasket and pressed in new one. Took about 5 minutes for both procedures. Vey Easy!

I shut the water off under the sink and removed the back piece on the refrigerator, unscrewed the water valve, cut the ends off each plastic hose and reinserted into the new water valve. Then rescrewed the water line into the new water valve and turned on the water. Unfortunately, I was not able to get water out of the door and the ice maker still doesn't make ice. While this was an easy procedure, it didn't help me. I'm not sure I needed to replace the water valve.

put 4 screws in door handle everythings else just slides into place. took less than 10 min. frig look new again.

The shelf bin is a piece that anybody can clip it on the door in less than 30 seconds. No tools required, just simple common sense.

Very easy. I at first misunderstood the instructions. the fridge door remains closed. You pull out the water catch tray "outside" the door. someone said ice tray, thats why i thought i had to open the door to fix it. there are 3 screws that the water catch hides. once removed the control panel comes off which unplugs from bottom easily. then there are screws behind the control panel just removed. after those are unscrewed the rest tilts enough that u can uncrew the little metal bands that hold the arm. replace arm & reverse your efforts & your done. took less then 10 minutes.

The broken fan made my refrigerator sound like a lawn mower I pulled the refrigerator out of it's nook and disconnected the power, removed the back panel with my battery powered drill motor, slid the old fan off of motor shaft, slid the new fan back on ran it to make sure the problem was corrected. The entire repair took less than fifteen minutes and was as simple as it could be. Please be careful when cleaning your coil, as the fan is easily damaged if you should contact it.

The most difficult part was the removal of the existing fan and shroud. There is very little room to work between the condenser and the coils where the fan is located. The old shroud had to be removed as it was not compatible with the mounting for the new fan motor and blade. Make sure to unplug the refrigerator and give the coils some time to cool down. The first step was to remove the old fan blade... it simply pulls off. Next you need to remove the two bolts holding the fan shroud to the floor of the refrigerator. Then you need to remove the old fan motor from the shroud... unplug the wire connection and remove two small bolts that hold it on. I was lucky to have a VERY small ratchet to get into these tight spaces. Now is the really hard part, removing the metal fan shroud takes a lot of twisting and turning to get it out. The coils have a little play in them, but you must be very careful of the tubing and connections. Also, the coils are very sharp. Once this is out, IF you can get it out....I had my doubts along the way, you can start to put the new parts in... beginning with the new fan shroud which fortunately is made of plastic and has some give which makes it easier to get in. Then you can mount the new motor to the shroud with the three new screws. Plug in the wire connection, add the foam tape to the shroud and mount the shroud to the floor of the frig with the original two bolts. Lastly, attach the fan blade. This replacement kit is well constructed, fits perfectly and contained all the necessary parts (fan motor with wiring connection, mounting screws, wire connection adapter, fan shroud, foam tape and fan blade), but no detailed instructions come with it. I was lucky to get the old fan shroud out without doing any damage to the surrounding parts, but this part was very difficult for a do it yourself person. I would be interested to know if a professional has some other tips for this part of the replacement process.

Unscrewed screw holding plastic clip on right hand top hinge. Unfasten two lags screws holding right hand top hinge. Lift door off bottom hinge. (Do not unfastened bottom hinge) Remove old plastic bearing and replace with new. Repeat aforementioned instructions in reverse order. DOG EASY.

One of the bins on my freezer door had the tabs, that hold it on the door, broken off. I orginally ordered the wrong item, but I called right away and Parts Select had the correct item to me immediately. It was a very easy fix, I just had to snap the bin in place once it arrived.I am very impressed with PartSelect and their service. I would definately use them again and recommend them to others.

Unplugged fridge from outlet. Removed rear panel on freezer side. Removed defrost thermostat from tube and cut wires. Installed new thermostat by matching color coded wires and crimping with supplied connectors and snap back on tube. Reinstalled panel and shelving.

The new bin arrived, I slid it in place and away we went.

door handle off but 2 screws top and bottom of handle that attach to door remained under top and bottom molding. had to remove molding which was tricky. Held onto door with plastic clips which several broke when trying to get molding off. Figured out I had to tap top molding up to remove. unscrewed pieces of door handle and attached new handle. Had to use contact cement to secure molding to door where clips had broken.

First I removed two screws per rail and removed the old rails. I replaced with the new rails and used a nutdriver to secure in place. This was extremely easy and I fell like my fridge is brand new again.
You can do it!!!