FPES18TCL0 Frigidaire Refrigerator - Instructions

Top freezer took off the panel in freezer and melted the ice around coils and found the defrost thermostat and replaced with the new one. Just followed the instructions from your video on line. Freezer works just fine now. Refrigerator is 38 years old.

My fridge side had warmed up to 70 degrees but the freezer side was still cold. The coils inside had iced up. After thawing with a hair dryer, it froze back after another week. I removed the old defrost thermostat and wired the heater strip directly and turned on the defrost timer. It began melting the ice so that ruled out the heater strip being bad. I couldn't get a reading with my ohm meter on the defrost thermostat so I took a chance and bought the part. Installation was a breeze and it fixed the problem.

I could not install, because I was sent the wrong part. I ordered a Left Side Cap and was sent a Right Side Cap the the Left Side Cap bag.

Unplug fridge. Removed 2 nuts to get the vent plate off and two more nuts to get the motor mount off. Removed fan blade and then the fan motor. I put the new motor in and put everything back as it was. It was very easy. I had items in the freezer, so I didn't turn the fridge off other than to replace the part. It took about 6 hours for the fridge to reach optional temps because I didn't get to defrost and the fridge had to work it out on it's own. If you don't need the freezer then you should turn the refridgerator off for at least an hour and open the doors so the coils can defrost and any ice blockage between the freezer and fridge portion can melt away as well.

Followed video instruction and completed the replacement. I had to join the wires since the connector was a male plug to a make plug.

Followed the instructions provided in your video, took less than 15 minutes and works like new. Thank you for the parts and the advice.

Unplugged the fridge. Removed water inlet valve from fridge. Used voltmeter to test for resistance (between 50 and 150 ohms). Didn't pass the test.
My original part was 218720400. I ordered part PS468507 from partselect.com. My original part had a "garden hose" coupling so PS468507 fit the bill.
This part's electrical connection wasn't angled the same way as the original so we had to finagle it.
Hooked the plastic refridgerator supply hose up first.
Then screwed on the copper "garden hose" connection to the valve using channel lock pliers. Was careful not to over tighten.
Then the fun started. The electrical connector wires were a tight fit between the copper tubing and the refridgerator frame. Did I mention that the electrical connetion wasn't angled the same as the original? My daughter got her smaller hands in there and was able to make the connection.
NOTE: Because of the angling issue I was unable to screw the anchor plate to the fridge.
I made sure that the valve did not interfere with the fan.
Turned on the water and checked for leaks.
Plugged the fridge back in and in a couple of hours we had ice cubes. Works like a charm!

just had to loosen the old, broken piece, and snap in the replacement. Piece of cake

Ordered the pairs of end caps for both the door shelves. The parts arrived the next day. Opened the wrapper slid the end caps on and attached the shelves to the door. Bingo!!! It was that Easy! Done in less than two days and less than $20. It took me some time to figure out if the parts were right though when I searched online.

Took old defrost pan off, put new one on. Had to bend new defrost pan a little for it to fit..

It was very easy. Pulled off the old valve and replaced with the new one and it started making ice right away. There are a couple of issues you need to be aware of that I am watching closely now. The old valve was a 15 watt valve. The one they sent me is a 35 watt valve. It really pressures the water into the ice maker. So much so I am getting a little leaking from the overflow. Its working so well and powering the water in so fast it starts to leak a little due to being to full. When I ordered the part, no where did it show the wattage of the valve so be careful. It works great but will have to keep an eye on it so it does not overflow.

Snapped in missing brackets, cut bar to fit and installed.

Just snapped in the wholes and pushed it down a little bit and there it was. It only took 2 minutes. Very simple process- price was supper and delivery was very fast.
Thanks guys- will order from you again

Made sure water was going into valve, shut off water to valve, removed it. removed two connections, replaced with new valve, Walla, off & running. Incidentally, rec'd new valve much quicker than I ever expected.

Since the end caps were already broken I just took them out & put the new ones in. Total time to do this was less than 5 minutes. Great parts, great prices & super fast shipping