FPD17TFF2 Frigidaire Refrigerator - Instructions

Just removed the two screws and unpluged it.
Then I pluged the new one in and replaced the screws. It runs like a brand new reffrigerator.
Thanks for the fast delevery. Will do busness with you in the future.

Cleaned insert hole, did a dry-run, then pressed everything permanently in place.

Removed two screws to get to defrost time pull panel down remove two screws holding time and reinstall

take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .

Removed front low grill, removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wires. Reversed process to install new timer.

Website was great!

The defrost timer was right in front. 2 minutes and a screwdriver and I had it replaced.

To replace the thermostat, I had to take out the back panel, defrost it and then install the new part. the only problem was that the heatshrink tubing they sent was too large. Otherwise, it worked great.

It snapped in place.

just like the video showed...it was excellent!!!

Slipped out the end caps with the broken prongs from the front rack and slipped in the new end caps. (3 mins.)

Put new end caps on door bar..put soap around door slots diped end caps in boiing water for 20-30 seconds and snapped in place

I HAVE SENT IN TWO STORIES I"M DONE OK
BUT THANKS FOR GREAT SERVICE

Thanks Steve 10-3-09

took 4 screws out of the discharge vent on top of the refrigerator section and unpluged the wiring harness and put the section on the counter and unscrewed the timer and put the new one in and reinstalled the assembly and plugged the Jack and put the 4 screws back in, and rotated the timer and put it on defrost removed the back and check the heaters and drain .

I found this website via a google search and clicked on the link suggesting solutions for the symptoms I had. I decided to order the part (defrost timer) that was proven the larger percentage of time to fix my issue (warm refrigerator) but decided to also purchase the evaporator fan motor as it was suggested by my brother to replace it as well. We powered off the refrigerator and removed the back wall of the freezer and completely defrosted the unit. This seemed to be the most work and longest time to complete. We used a hair dryer to do this. Once the ice was gone, we replaced the defrost timer, which seemed to fix the warm refrigerator part. We didn't immediately swap out the evaporator fan as the power plugs did not connect properly and it was a little confusing on how to accomplish this. I called partselect back and they didn't have anyone that could talk to me throught the replacement process but recommended we call frigidaire. Meanwhile, we found out that the defrost timer corrected the warm refrigerator and now that the evaporator fan could move (no longer frozen in ice) it was making a lot of noise. So we contacted fridgidaire, and they were able to provide me with a similar video on connecting the power between the new evaporator fan motor and the refrigerator. . We ended up snipping both power connectors (from fridge and new part) and twisted the wires togehter and now the fan is moving without noise, the freezeer and refrigerator is working like a champ! Very happy outcome!

I followed the advice posted by others at parts select website. This made the repair process easier. Everything went very well, and my refrigerator is working just fine. I definitely will use parts select in the future for any appliance parts and repairs I may need.

Removed the old burned out evaporator fan, and with the model# was able to find a replacement at PartSelect. I was really surprised that you had the exact part on a fridge that old. Installed the new fan, and the fridge is working beautifully. Thanks to PartSelect I was able to save several hundred dollars.

I original tried to repair the motor but was not able to. I remove the screws on the back plate and removed the the back plate. Removed the shroud for the motor and screws, unplug the power connection and removed the fan motor. Installed the new fan motor and reassembled everything. The refrigerator is working great.