FGS365ECA Frigidaire Range - Instructions

I removed the bottom of the oven and flame guard for access to the ingniter. I then replaced the ingniter. The oven works like new now.

Unplugged the appl. I removed the bottom of the oven. Disconnected the two wires. Removed two screws that hold the element in place. Replaced it. And put everything back together. Since this element goes bad about every year an a half, I keep one on hand all the time.

remove oven door, disassemble front of glass top range then basically
it was just plug and play then reassemble be careful oven door is heavy

This was very easy. Just remove the bottom of the oven by removing the two screw in the back. Then remove the baffle from under that and you of will see the ingniter. The one wire will reach the gas valve, just splce the other. 6 screws is all it takes. Turned it on worked perfectly.

replaced it

I cut the wires from the old igniter near where it said to. I then connected the new wires to the old ones, put it back on, the way I remembered it being assembled, but still won't heat up. I tried to get an enlarged detail of where I was working on, but I couldn't enlarge it from your website. My friend, who knows about electricity, worked on it for several hours last pm(He's an electrician), but could not figure it out with the scamatic that was on the range, because he was not there when I disassembled it,

The philip head screws holding the igniters were frozen. Had to cut off heads with dremel cut off tool, then grabed residual screw with vice gripp pliers. Removed screws and mounted new ignighters. Used new hex head bolts. Attached wires per instruction sheet and tested unit. It worked.

took the old igniter out and swapped the connectors onto the new one. Kept the connectors close to the connector end to prevent them from being to close to the ovens heat.

Removed the two screws, took out the old one and replaced the new one. It was very easy and the oven works great now. Thanks.

Replaced the flat style oven igniter. Turn off gas and unplug oven. Removed the broiler drawer, cut wires, unscrewed oven igniter (using a small/medium adjustable wrench), connected wires, fastened new igniter to bracket, spliced wire, twisted together, plugged oven back in, turned gas on, turned on oven after a few minutes...worked great.

Removed 2 screws to oven bottom
Remove one nut that holds gas rail deflector
Removed 2 screws that held Igniterto the fuel rail
Cut 2 wires to the Igniter
attached 2 wires from new Igniter using ceramic wire nuts (Suplied with new part)
Install same as removal

I just sent in a generic description of my problem and a couple of ideas on what it might be. Within 2 days an online repair person answered me back with the solution. I ordered the part and 2 days later I was back in business and baking cookies.

pulled stove out to unplug the electric cord. Took oven door off and removed the bottom panel (2 screws) and then removed the burner (2 screws). took off old igniter ( 2 nut screws). cut wires and stripped the coating to wire to new unit.
Attached new igniter to the burner, and put the burner back in place and replaced the screws so unit was stable.
Turned oven on to make sure ingiter was going to light oven, when oven came on, turned oven off and replaced the cover to the burner and the bottom panel in the oven,. Put the oven door back on........
Probably took 45 minutes.
I ordered the part late Friday afternoon, around 3, and the part was here Saturday Afternoon. I was impressed.

I removed the oven bottom which was held by two large head long screws. I then removed the heat deflector using a small socket. The only difficult part was when I went to replace the igniter. The screws that were holding it in place stripped I guess do to the amount of heat they were continually subject too. I had to apply pressure to the igniter bracket while removing the screw using a small socket. Even with that they did not come out easily. If I had not had trouble removing the screws the repair probably would have taken 15 min.

followed the instructions that come with the part. very quick and easy.