FGP337HW0 Roper Range - Instructions

It is very simple to do. We called a repair man we normally use, but he does not do gas appliances. So started to research. I removed the bottom drawer, looked at the connection on the wires hanging down. Opened the oven removed the racks. On the bottom plate, loosened two screws and slid the bottom toward the front and removed it. Then removed two philips screws and removed the heat deflection plate, it slides forward and pulled up from the back. Then there it was- the igniter. I looked at it then looked at the connection behind the drawer. Went to PartSelect.com, found the part using the model number and used the parts diagram found the igniter and the picture matched what I had. I ordered the part, placed all parts back in place until part arrived. After part arrived, shut off breaker to oven removed all parts again disconnected the wire connection behind the drawer. Then on the side of the igniter, I used a nut driver, removed two bolts and took out the igniter. Matched it to the new one, including the power connection. Placed new one in and reversed the order. Turned on breaker, Pre Heated oven, been in service since. Ordered part before 3 on Wed, received early on Friday. Stopped home during lunch Friday and put it in place. 15 minutes and DONE Oven worked and fresh baked cookies when I got home! Thanks PartSelect.com!

We looked up the trouble shooting page on PartsSelect and ordered the part recommended. Part arrived very quickly. Simple installation, two screws and plug in. Problem fixed.

I removed the bottom srtip. Installed the new bottom strip, snapped in the side pieces. [The old ones screwed in.] Replaced the original handle. Ready to reinstall door.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Replacing it was just as simple,only in reverse.
The only tip I have that I should mention,is to UNPLUG the appliance first,as 110volts tingle your fingers!

Found that the two screws securing the bottom had rusted away allowing me to just lift the old bottom out. The new one fit in place exactly and really did not need the screws. Done in 2 minutes.

New ignitor fixed the problem

Pull bottom draw out and there it was

it took 2 people to do this job. we had to place a yard stick inside the door to keep it open because after we removed the 2 screws inside the door that held the handle on, the door would not stay open. after removing the handle we had to slide the glass down from the top and line it in the slots at the bottom and then we had to replace the handle back on top of the stove, lining up the slots and the side pieces. after that we screwed in the 2 screws and yea! we did it right. The glass is in and we managed to not break it!

Unplugged 110 cord from outlet. Shut off gas supply. Removed rear cover (4) screws to access plug to ignitor. Removed boiler stove bottom drawer to access ignitor removed 2 machine screws 5/16 nut driver for ignitor replaced ignitor. I did no trouble shooting just took logical guess.

I removed the two screws that held the igntr in place. Then I pulled the igntr out and unplugged the wires. Replaced the igntr with the two screws and plugged the wires back together. I then turned the oven on to 400 degrees and it heated like a new one.

remove the hinge stays they just clip in
remove the door. took out screw at bottom of door.
replaced trim.
replacing the door was a problem i didn't have pins to put in the spring loaded hinges so i used nails to hold hinge in position.
so make sure to open oven door first insert pins or nails in hinges then remove door. It would have took 10 min. to do.

Remove 2 screws holding oven bottom in place.Lift out the plate and replace with new plate. The hardest part of the replacement was lining up the screw holes. By the way i have never received such great service from any internet company as Part Select. I ordered the part on a Monday and the part was at my home the NEXT DAY and installed that evening.

This repair was easy as could be to screw take off the diffuser four screws in the back two little screws on the igniter

Un-screwed 4 screws. Got part numbers off of the pieces. Put numbers in blank on web site and ordered the pieces. Parts cam in 4 days later and installed the pieces with my trusty screwdriver.

After I found the web site I looked at the possible solutions for my problem. My igniter was glowing so I was not sure that would fix the problem but several places indicated the igniter would fix the problem and after I replaced it the oven work great.