Quick Question!

Have you ever purchased from PartSelect.com before?

Models > FGP305KW2 > Instructions

FGP305KW2 Roper Range - Instructions

All installation instructions for FGP305KW2 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FGP305KW2
16-30 of 48
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Gas oven only lite periododically

  • Customer: Dan from KIESTER, MN
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 4 people found this instruction helpful
Unplugged 110 cord from outlet. Shut off gas supply. Removed rear cover (4) screws to access plug to ignitor. Removed boiler stove bottom drawer to access ignitor removed 2 machine screws 5/16 nut driver for ignitor replaced ignitor. I did no trouble shooting just took logical guess.

oven would not light

  • Customer: Sandy from WILLCOX, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 2 of 2 people found this instruction helpful
I took apart the bottom of the oven to see the ignighter. I moved the oven away from the wall and took off the metal plate that covers the ignighter electrical connection.Unplug the old part and plug in the new one. With the nutdriver remove the two screws holding the part onto the gas tube. Save the screws and attach the new part with them. Turn on the oven to see if the gas tube lights. If all is good put the metal plate on the back of the oven and replace the other oven parts. Make biscuits!!

oven igniter quit working

  • Customer: Paul from MORRISTOWN, IN
  • Difficulty: Very Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 2 of 2 people found this instruction helpful
pulled the stove out removed back cover, unplug then unscrew igniter. Mounted new igniter in place, plug it back in , put cover back on, put stove back in place. Took about 20 min. Very easy repair, thank you.

the handle supports too long for this model

  • Customer: Theodore from Glenside, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 6 people found this instruction helpful
cut 3/8" off each handle supports and used no. 10 1/2' sheet metal screws to secure handle and door front to the oven door. The supports had to be shorten to allow the door front to fit correctly on the oven door.

missing handle

  • Customer: Catherine R from Cadyville, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
the part would not install in the opening

I was trying to remove the oven door so I could clean the glass. Spills had run down between the layers of glass.

  • Customer: Karen from Oklahoma City, OK
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.

Replacement

  • Customer: Lynn from McLean, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
Unscrewed old handle and tried to fit new one on;

The door handle broke and had to be replaced

  • Customer: dominic from Tucson, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 6 people found this instruction helpful
I removed 3 screws to take the old door handle off; the screw on top of the door and 2 screws that screw into the handle on the 2 corners of the door inside the oven. Removing the 2 screws lets the outer and inner door panels seperate so you can see that there are 2 retaining washers on the 2 ends of the door handle inside the outer panel. I removed these 2 retainer washers from the old handle; then put the new handle and the 2 retainer washers on the outer panel. The new handle is put on the door by closing the inner and outer panels and replacing the 3 screws.

Oven would not light

  • Customer: Gary from Springfield, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Opened lower door of stove located ignitor removed 2 small screws that secure part, took guard off back of stove unplugged wire connector removed part plugged new ignitor in re-installed guard, re-installed 2 screws that secure ignitor. Turned stove on oven lit problem solved. This is the 3rd time i have used instant repairman on parts select to fix 3 different applicances and have saved hundreds of dollars fixing it myself with the help of parts select.

The Oven Did Not Come On.

  • Customer: lore from lampasas, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
It only took my husbend 6min to put in the new oven igniter. But it did not work, so I call your center and the rep there talk my husbend and told him how to unluck the key bord, and that worked. Thank you for all the help.

oven igniter

  • Customer: Kasey from Stryker, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
ordered the part and in less then 24 hours from ordering the part it was shipped and delivered and my husband and I put the part in took us no time at all very easy to do... 2 years ago i had this same problem and called a guy in the area cost me $200. I had dinner in the oven by 5 that night!!!!

Oven would not come on.

  • Customer: Edie from Paducah, KY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I removed the oven racks, removed the oven floor and the oven burner cover, pulled the range out and removed the small panel on the back which covers the igniter connector. I disconnected the old igniter, removed the two screws holding the igniter in place and removed the old igniter from the oven. Then screwed on the new igniter, fed the wire through to the back and connected the new igniter. Turned on the oven and voila' we have ingnition! The oven is working again but I'm getting the "F2" routine sometimes. It doesn't do it every time but when it does I unplug and replug and then it works. I'm a 67 year old female and I considered it very easy so pretty much anyone should be able to do this repair.

Igniter went bad so gas wouldn't fire up

  • Customer: Mick from Indianapolis, IN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed a cover plate on the back of the stove. Unplugged the old igniter. Pulled the bottom drawer out. Reached in under the stove and undid the 2 screws holding the igniter in place. Screwed the new igniter in and put everything back together. The only tricky bit was reaching the igniter through the bottom drawer opening.

old igniter glowed red but was too cold

  • Customer: dominic from Tucson, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Shut off gas and unplugged electrical cord. Removed grates; oven floor and flame spreader and then unbolted old igniter with nut driver. Removed shield in rear of over with Phillips screwdriver and unplugged igniter from power socket. Removed old igniter and replaced with new. Bolted new igniter into place with nut driver and plug into rear socket. Turned on gas and plugged in electric to test igniter; saw white glow and flame on in a minute. Replaced rear shield, flame spreader, oven floor and grates. DONE!

The oven wouldn't light.

  • Customer: Jim from Broadalbin, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Our oven wouldn't light as the ignitor wasn't getting hot enough. I ordered the part from your company and got it in just a few days. A quarter inch wrench and one plug, done!
All Instructions for the FGP305KW2
16-30 of 48