Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This dishwasher door gasket (Bottom Gasket, Gasket, Door Seal, Dishwasher Door Lower Seal) helps prevent water from leaking out of the bottom edge of your dishwasher door by creating a watertight seal...
The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, o...
This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing wate...
This spray arm is a genuine OEM replacement part for your dishwasher. This spray arm is for the upper part of your dishwasher. No tools are required for this repair, simple remove the rack stops and u...
This water inlet valve is usually located behind the lower kickplate panel in either the right or left corner of the dishwasher. The attaching solenoids on the valve open and close according to the de...
The silverware basket, used for dishwashers, is in the bottom dishrack. The lower dishrack basket is used to hold eating utensils such as spoons, forks, and knives, and other small tools. If the baske...
The heating element nut is used to connect the heating element to the dishwasher tub. If water is leaking from underneath your dishwasher, you may need to tighten or replace the heating element nut. R...
This part is a replacement spray arm support for your dishwasher. It is made of white plastic and is approximately 3 inches long, 1 inch wide, and 3 inches tall. This is the support for the lower spra...
The upper dishrack roller and axel kit comes with two pieces, a wheel and an axle. This kit is made for your dishwasher. Both pieces measure to be roughly one square inch each, they are made entirely ...
If your dishwasher is leaking or not draining properly, you may need to replace the drain hose. The drain hose connects to the pump located below the lower spray arm and aids in proper dishwasher drai...
This dishwasher door latch assembly is a critical component designed to ensure safe and efficient operation. It features an integrated switch that functions as an on-off mechanism, preventing the appl...
This splash shield kit is used in dishwashers and is attached to the lower front corners of the tub. The splash shield is used to prevent water from spraying past the door seal. If your dishwasher is ...
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
20 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Chuck
October 8, 2021
Dish washer starts then stops with pf indicator
For model number FGHD2433KF1
Hello Chuck, Thank you for the question. The Power Failure Error code can indicate a interruption in power. You can try to reset the appliance by disconnecting power at the breaker for a few mins and restarting. You can also try to Press the "Start/Cancel" button to clear the "PF" error code. We hope this helps!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Steve
January 6, 2024
My Frigidaire dishwasher door opens lower (more than level) and I think the spring or cable may be broken? What do you think?
M# FGHD2433KF1
S# TH94647585
How many do I need?
What are the part numbers for each?
Can you determine the manufacture date of this machine?
For model number FGHD2433KF1
Hello Steve, Thank you for your inquiry. We recommend checking the hinges-which come as a kit, door springs-most models require two and cable friction cables-most models require two. Based on your model and serial number, we show that this model was made in November of 2009. Good luck with your repair.
Dishwasher will not drain completely. I can press the start button and hold until the washer begins to drain manually. After a few times it will gradually drain completely. Wondered if it was the drain timer circuit on the board.
Thanks.
For model number FGHD2433KF1
Hi James, thank you for reaching out. The fact that it drains completely after a few attempts suggests that the drain pump and hose are likely not clogged. The issue could be with the control board, part number PS12365809. It manages the functions of the dishwasher, such as washing, draining and drying. We hope this sorts out your problem!
Heating element on all the time and overheating, I already changed the thermostat and didn’t do anything still overheating, I have to unplug to turn it off
For model number FGHD2433KF1
Hello Bruno, thank you for getting in touch. We would recommend replacing the control board, part number PS12365809, to fix the issue. We hope this helps!
I am getting the message "er" on my Frigidaire dishwasher. What does it mean? How can I fix it?
For model number FGHD2433KF1
Hi Susan. This is a keypad error you can try to power-cycle the dishwasher. However if this does not work you will have to replace the keypad. Thank you for your question and good luck with your repair!
Repair was simple. I unscrewed the old grommet which held the old spray arm and screwed-on the new one. About 30 seconds was required. Other people having this problem should note that the spray-arm is made of three pieces which are inseparable when the arm is new. The arm is sold in this form. However, when your machine is having th
... Read moree problem that the arm falls off, the three pieces become separate. When you want to replace the spray arm, only one new part needs to be ordered because this part encompases all three components.
Remove the bottom cover plate. Disconnect the water inlet and black rubber hose. Remove 2 mounting screws. Pull out electrical connector. Reverse order. Be sure to get the brass inlet connector really tight so it won't leak. I did the final tightning after the part is mounted. Not a bad repair at all. The only problem was that it
... Read moreleaked in the first place and messed up my subfloor and laminate flooring.
