FGF337EWC Frigidaire Range - Instructions

AS YOU DESCRIBED IN YOUR YOU-TUBE VIDEO, THE OVEN IGNITER WOULD GLOW BUT THE OVEN WOULD NOT LIGHT. YOU EXPLAINED THAT THE PROBLEM COULD STILL BE THE IGNITER AND SO I ORDERED A NEW IGNITER AND THEN WATCHED YOUR VIDEO ON HOW TO ACCESS AND REPLACE THE NEW IGNITER AND THAT FIXED THE PROBLEM. I ONLY HAD TO CUT THE OLD WIRES ON THE OLD IGNITER AND MATCH WIRES WITH THE NEW IGNITER USING THE CERAMIC WIRE NUTS SUPPLIED, AND I WAS BACK COOKING AGIN. THANKS.

Removed oven door, removed oven floor. Unscrewed skirt with attached igniter and gas tube. Two nut screws hold igniter to burner. Remove old igniter and replace with new, reattach two wires with supplied wire nuts. Replace oven floor and door. Oven lit right up, pizza anyone?

Removed the metal cover on the back of the range by unscrewing the square-drive screws around the perimeter, left the center screw until the end to make it easier to hold for removal.

The control unit was held in with 4 Philips head screws, and connected by a single wire-to-board connector. Unplugged the connector and removed the screws and the control unit came right out.

The replacement unit doesn't come with a face plate, so I used a razor blade to carefully remove it from my old unit. The adhesive that held it on was still sticky so I was able to easily attach it to the new unit.

Then I just put everything back together in reverse order. One of the easiest appliance prepares I've done.

Watched a half dozen You Tube Videos before I saw the Exact one-Submitted by a Woman-Super Easy-Had the Exact Part from this site!

First thing is I looked for videos on how to replace oven igniter to get an idea. Unplug AC cord and turn off gas valve.On my model I was not able to figure out how to remove oven door. You can still work around it without removing. Inside the oven, remove bottom cover. Remove 2 screws located in rear corners. After removing oven bottom cover, next is a burner cover. Remove 2 screws located toward front of oven using a nutdriver or socket. After removing burner cover , you will find oven igniter. Now remove bottom drawer. This is why its a bit difficult for others. Igniter has 2 leads. Laying down on the floor and reaching in to follow-identify where the 2 leads go to. Using same nutdriver or socket remove 2 screws that hold up the igniter. I cut the leads from the base of the old igniter so you will have some slack to work on when you reconnect the wires underneath. Install new igniter, run leads same way.Strip back about 3/8 in. wire, twist leads to proper wires and twist on ceramic wire cap that is provided. Make sure no bare wires are exposed! Now you can test.

open oven door remove bottom of oven then remome the metal cover over the burner to expose the ignighter remove 2 screws that hold it to the bracket. the two wire's that come out of the ignighter run down under the bottom oven pan, i removed the bottom front cover by lifting up and then pulled out, then i could see the wires i removed the wire nuts and pulled old wires off and removed old ignighter. i pulled off the insulator covers from the old one and slid them on the wires of the new ignighter then i fished the wires back down and and attachted them with the wire nuts, then reasembled the rest of the oven. woks great!

Removed lower drawer of oven and base panel of oven. Unplugged stove from outlet. Removed old igniter w/ nut driver (two screws). Disconnected wires (blade connectors) from stove base. Disconnected two-pole plug from oven after removing protective cover in corner.

Install new igniter. You will need to cut existing wires from old igniter so that spade and two-pole connectors can be reused. Join these wires with the new ignitor wires using the ceramic wire nuts provided with the new unit.
Directions are also provided with the new igniter.

First I removed the two screws that held the element in place. I then pulled the element out about 3 inches and disconnected the two wires nuts, (from last repair) installed new igniter. Not rocket science here.

Took out old screws and replaced with new

CUT THE WIRES ON OLD IGNITER AND WIRE NUT THE WIRES OF THE NEW IGNITER TO WHERE I CUT THE OLD ONE OFF.

1. Removed top over the oven burner.
2. cut the two wires conneted to the igniter about
an inch and a half.Noted which wire goes to the top of the igniter and which one went to the bottom.
3. unscrewed the igniter from the mount and
carefully pulled it from the oven.
4. put the new igniter wires through the hole.
5. mounted the igniter to the burner.
6. attached the new wires to the top and bottom old wires with the connectors that came with the igniter.
7. pluged the range back in and turned on the oven. Igniter works great.

take off the old by unsceawing it scraw thenew one onput the wires down the back throw the hole put the wires to gather and cap tham plug the elect. back in and turn it on for to test it wow it worked he he ...richard

First I removed the two screws that held the element in place.I then pulled the element out and cut the wires.I used wire nuts to put the new wirers on and put it back in place with the two screws.I tried it and it worked perfect.

removed broiler front by depressing the indents on the door slides, removed two screws holding igniter cut wires on old igniter and spliced new igniter to existing wires with supplied wire nuts then reinstalled new igniter and tested have been using oven ever since

Easy installation using a nut driver and a Phillip screwdriver.plug in harness connector and done.