All Installation Instructions for Frigidaire Range FGEF3036TDC

oven took too long to heat up

un bolted the 6 nut driver heads found probe wire un pluged it 1/4 turn from lock it was in and pull out replace slide in new probe 1/4 turn to lock it in place replace nut driver self tappers and test simple!!

Parts Used:

Temperature Sensor

JAONNE from GAFILED, NJ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

Was this instruction helpful to you?

broiler element burned out.

Unscrewed the old element (2) screws, then unscrewed the (2) brackets holding the element up, pulled the element out of the back wall of the oven unhooked the (2) electrical wires and left them hanging. Installation is in the exact reverse order.

Parts Used:

Broil Element

Kellyjean from Springfield, MA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Broiler element broken

Removed broken element, four screws. Element ends were attached to the oven via wire clips. Removed those too. Placed clips on the ends of the new element and remounted to the top of the oven enclosure with the fours screens. Took twenty to twenty five minutes. We had Tbones a little while later. Saved over 125.00 for repairman.

Parts Used:

Broil Element

Robert from Newark, DE
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

damaged bottom pan

Removed 2 back screws, lifted pan from rear and pushed front slightly forward/into oven until front lip cleared. Installed new pan in reverse order.

Parts Used:

Bottom Panel

Neal from Severna Park, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

aluminum foil melted on oven bottom

It cannot be cleaned as it welded itself to oven bottom. Two screws in back of oven bottom and it lifted right out. The new bottom says "do not use aluminum foil" Very easy repair.

Parts Used:

Bottom Panel

Allen from wakefield, RI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Aluminum foil on bottem of oven melted and made a mess on new stove

Unscrewed the oven bottom plate and removed. Put new one in place and screwed it in place. Stove looks brand new again and am so happy with the results.The part we received was a perfect match and arrived in a few days!

Parts Used:

Bottom Panel

Natalie from Beaverton, OR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Broken oven door glass

I followed directions for replacement of the glass from the web. Replacement was simple and easy.

Parts Used:

GLASS

Joseph from Cranberry township, PA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

broken inner glass

Removed oven door. Removed screws from bottom of door as well as handle screws. Remove inner panel to expose glass. Replaced glass panel and reverse steps. Very easy.

Parts Used:

GLASS

Neal from Warsaw, IN
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Purchased home where previous owner melted Aluminum Foil to bottom panel of oven.

Removed 2 screws from rear of panel and dropped new panel in. Re-installed screws. Oven like new again. Aluminum foil was burning and emitting foul odor when oven was on.

Parts Used:

Bottom Panel

Michael from Wimauma, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

no heat

Replaced the oven probe because a no heat problem. also had to replace the oven control. That was a bit expensive but still saved me hundreds not calling a serviceman. By the way, it works like new.....

Parts Used:

Temperature Sensor

John M. from PLEASANT PRAIRIE, WI
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Needed to install an anti-tip bracket on my stove.

Moved the stove. Used the template to position the bracket. Put the supplied screws to attach bracket to the floor. Slid stove back into place. DONE!

Parts Used:

Anti-Tip Kit

Daniel from Provo, UT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

Was this instruction helpful to you?

really bad ugly streaks inside of glass

open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door. Just reverse the way you take it apart to put it back together.

Parts Used:

GLASS

John from Hemet, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

put aluminum foil on bottom panel of oven to catch drips. Big mistake. adhered to oven in minutes.

Removed 2 screws at rear of bottom panel. Removed old panel, replaced with new and screwed back in.Piece of cake. Plus this company was great to order from. received part the same day. Very happy. Would order through this company again.

Parts Used:

Bottom Panel

jill from new boston, NH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Small plastic lens on control panel broken.

Pulled the range out, unplugged it, removed upper back panel, inserted lens through front of control panel, slid the notch on the actual light onto the lip on the back of the plastic lens. Done!

Parts Used: