Models
>
FGC3X4XAW1
FGC3X4XAW1 Frigidaire Cooktop - Overview
Sections of the FGC3X4XAW1
[Viewing 2 of 2]
Keep searches simple, eg. "belt" or "pump".
Surface Burner Igniter Electrode
PartSelect #: PS436633
Manufacturer #: 316011200
Use this igniter with sealed burners.
$32.04
In Stock
Top Burner Mounting Screw with Washer
PartSelect #: PS437925
Manufacturer #: 316069301
This is now a new zinc and black-coated screw that will resist rust and
seizing.
$1.80
In Stock
Spark Module
PartSelect #: PS2350722
Manufacturer #: 316135702
This spark module or range spark module, is used in ranges and ovens. The spark module monitors and controls the spark to ignite the surface burner in a range. It does this by sending a certain amount...
$94.31
In Stock
Small Burner Base with Orifice and Igniter
PartSelect #: PS470099
Manufacturer #: 5303935025
This part also includes 3 screws. Small burner cap is sold separately.
No Longer Available
Igniter Switch
PartSelect #: PS437310
Manufacturer #: 316032002
When the gas burner valve knob is depressed and turned, this part creates a spark that lights the gas and starts the burner.
$55.82
Special Order
Gas Pressure Regulator
PartSelect #: PS473609
Manufacturer #: 5308007974
***No Conversion Kit Required - Adjust On Appliance***
This valve automatically cuts off the flow of a liquid or gas when it reaches a certain pressure.
$250.69
In Stock
Questions And Answers for FGC3X4XAW1
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the FGC3X4XAW1
[Viewing 3 of 3]Will Not Start
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Igniter porcelain was cracked and burner would not light.
un-pluged stove,removed the one screw holding the broken igniter. disconected the one wire. installed new igniter and slipped on wire. The igniter came with a new bracket, the old one rusted away which is why the old igniter broke.
Parts Used:
-
Rusty from Howell, NJ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
53 of 76 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bad igniter.
The stove was older so the burner was hard to get out. The small screw heads broke off, so I had to carefully center punch and drill out the screw bodies. The igniter screw was also frozen in the pot metal burner. That screw requied drilling and tapping with the installation of a new 6-32 screw. Once the burner was refurbished, the igni
... Read more
ter mounted easily. Afte attaching the gas line and igniter wire, the burner worked great.
Read less
Parts Used:
-
chris from Venice, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Wrench set
15 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner would not lite
no need to remover burner. Lift top up use a 1x4x5" to hold top up. Use short #2 screw driver remove screw and replace with new igniter
Parts Used:
-
Terry from Wilkinson, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
12 of 16 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!