All Installation Instructions for Frigidaire Refrigerator FFHT1614QZ0

2 drawer undercounter beverage ref not getting cold enough. Wont get below 48°

Took drawers out by removing 2 screws on top of rail near front, then popped black plastic cover off in lower right inside cabinet...sensor just un plugged and new one plugged in easily...did not fix problem though...display set at 34 but bottom drawer reads about 40 at best and upper drawer reads around 55...dont think the 3 little fans inside on back wall have been running

Parts Used:

SENSOR,TEMPERATURE,10K,NTC

Tim from SYLVANIA, OH
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

8 of 11 people found this instruction helpful.

Was this instruction helpful to you?

Oven light bulb went dark; it needed replacing

Twisted replacement bulb into place easily. Let there be light!

Parts Used:

Light Bulb

Lise from CEDAR GROVE, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

10 of 17 people found this instruction helpful.

Was this instruction helpful to you?

Refrigerator Light bulb went out

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

Parts Used:

Light Bulb

ANGELA from MEBANE, NC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

7 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Missing door rack

Just snapped them into place without any problems! The parts were exactly what I was looking for.

Parts Used:

Door Rack

Bryan from Minneapolis, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

6 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Warm fridge and freezer

After checking the capacitor and 3 in 1 starter run relay for continuity and both measuring , I was able to remove the old parts and install the new parts for the refrigerator after unplugging the unit. I also checked the new parts prior to installing. I also went on Parts Select and watched some very helpful videos. Thanks a lot for your help desk for going above and beyond to ensure that I ordered the correct part! ????

Parts Used:

Start Device

Run Capacitor - 120V

Bruce from TEMPLE HILLS, MD
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers

5 of 5 people found this instruction helpful.

Was this instruction helpful to you?

broken restrained rack

The old one popped out, the new one popped in. As easy as that.

Parts Used:

Door Rack - White

Anthony from LANCASTER, OH
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

door rack broke in half

opened thepackage snapped in place .took all of 3 minutes

Parts Used:

Door Rack

Roberta from Port William, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

5 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Door handle was broken

It was extremely easy. I opened door, unscrewed the two (2) screws at the top of the door handle with a phillips screw driver. Once screws were out I rotated the handle to the left and unhooked it from the mounting block. The new handle was already equipped with a mounting block. I attached the new handles mounting block to the door and rotated the handle up and positioned the holes to the holes on the door. I used the same 2 screws from the old handle and tightened them into the handle and door. That was it. Very easy.

Parts Used:

Refrigerator Handle set (2 pieces) - White

Tammy from SAN ANTONIO, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Door sagging, creating a gap to let in condensation

You tube is my best friend for DIY repair. I supported the door with wood blocks, removed the bottom bracket and was able to slide the refrigerator door down and out without removing the freezer door. Replaced both hinge bearings and door stop and washer on bottom hinge and slid the door back into place. Door is very light when empty. Fast and easy, door opens and closes smoothly and no problem with condensation anymore.

Parts Used:

STOP-DOOR

Hinge Bearing

Single Washer

amy from SOMERVILLE, MA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

replace a broken door handel

Very simple. Remove the 2 top screws on the door, slide the lower part of the handel on to the lower screw on door .,swing the handle up to the top of he door and attach with the 2 original screws. DONE

Parts Used:

Refrigerator Handle set (2 pieces) - White