All Installation Instructions for Frigidaire Refrigerator FFHS2322MBHA

Broken Shelf

Slid the shelf in place!

Parts Used:

Door Shelf Bin

kevin from erie, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

8 of 11 people found this instruction helpful.

Was this instruction helpful to you?

door bin broken

very easy to do. just snap into place

Parts Used:

Door Bin

ROBERT from WARDENSVILLE, WV
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

7 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Switch would not allow door to close.

Removed screws holding unit and removed unit. Removed switch from connectors in unit. Replaced unit without switch. On day switch arrived (delivery was prompt) my wife replaced switch by attaching the two connectors and slipping into unit without having to remove entire unit. How easy was that!!!

Parts Used:

Light Switch

Charles from Front Royal, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

7 of 8 people found this instruction helpful.

Was this instruction helpful to you?

2 drawer undercounter beverage ref not getting cold enough. Wont get below 48°

Took drawers out by removing 2 screws on top of rail near front, then popped black plastic cover off in lower right inside cabinet...sensor just un plugged and new one plugged in easily...did not fix problem though...display set at 34 but bottom drawer reads about 40 at best and upper drawer reads around 55...dont think the 3 little fans inside on back wall have been running

Parts Used:

SENSOR,TEMPERATURE,10K,NTC

Tim from SYLVANIA, OH
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

8 of 11 people found this instruction helpful.

Was this instruction helpful to you?

The Ice Crusher Did Not Work And The Bin Was Carroded From A Previous Owner

I removed the ice container found the part # on the bottom ordered a new one and installed it. It just slipped right in to place.

Parts Used:

Ice Container and Auger Assembly

Imogene from Truth or Consequences, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

7 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Frost build up on evaporator

Remove the bottom freezer drawer. Remove back metal evaporator panel. Wire in new defrost terminationT-stat. Reassemble evap panel. Good to go.

Parts Used:

Defrost Thermostat Kit

B J from Dillingham, AK
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

12 of 24 people found this instruction helpful.

Was this instruction helpful to you?

EVAPORATOR FAN MOTOR & BLADE

The service manual diagram shows the 149 complete fan shroud in a vertical (upright) position. Misleading! Of course.
The actual mounting of the lay in fan shroud fully assembled is in the horizontal position laying in a tray area just above the evaporator coil cage assembly. The entire shroud assembly can be installed incorrectly by the diagram and will still fit. BUT... no cold air will flow or be forced into the ice maker vent nor the refrigerator vent. I found this out the hard way by trial & error.
If the drawing had shown it in the horizontal position for both removal and reinstallation... it would have saved a lot of time and headaches. Also, the diagram does not show the (2) plastic angle supports on the shroud, another scratch your head event. Parts included on drawing... 149, 5, 8, 9, 13, 14 on CTFFHS2611PF4 diagram page of service manual.
ALSO, the (4) lower cabinet plate screws have to be removed, and the first left hand screw counting up to allow the next upper panel to swing out enough to lay the shroud in correctly (horizontal) on top of the evaporator coil cage. BOTTOM LINE... THE AIR FLOW HAS TO BE UP IN ORDER TO WORK PROPERLY.

Parts Used:

Evaporator Fan Motor

Evaporator Fan Blade

Glen from HENDERSONVLLE, NC
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

6 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Warm fridge and freezer

After checking the capacitor and 3 in 1 starter run relay for continuity and both measuring , I was able to remove the old parts and install the new parts for the refrigerator after unplugging the unit. I also checked the new parts prior to installing. I also went on Parts Select and watched some very helpful videos. Thanks a lot for your help desk for going above and beyond to ensure that I ordered the correct part! ????

Parts Used:

Start Device

Run Capacitor - 120V

Bruce from TEMPLE HILLS, MD
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers

6 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Water dripped from water outlet on door

Replaced the Triple Water Valve

Parts Used:

Refrigerator Water Inlet Valve

Douglas from Denver, IN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

chrisper drawer jammed found supports were broken

Looked at video on how to remove and reinstall support and followed the instruct ions

Parts Used:

Crisper Cover Support - Front

Crisper Support - Rear

ROMAN from COLTON, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Refrigerator Light bulb went out

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

Parts Used:

Light Bulb

ANGELA from MEBANE, NC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

7 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Support stude for both vegetable crispers broken off

Support studs have an expansion fitting - center post has to be pushed through to allow expansion joint to collapse for removal. After installation, this post can be pushed in or pulled out to secure the stud and be the proper length to hold the bins.

None of this was obvious - an online tip from another member was invaluable.

Parts Used:

Crisper Cover Support - Front

RANDY from NORTH CHARLESTON, SC
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Freezer not holding temp

The repair could not be completed. I ordered a thermostat defrost kit but received a collar arbor for a saw. They do not answer the phone at customer service and the order took close to two weeks to get in the first place. Beware of shopping at this site!

Parts Used:

Defrost Thermostat Kit

David from MILTON, DE
Difficulty Level:
Difficult
Total Repair Time:
More than 2 hours

5 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Replace ice maker which was splashing water

Turn off ice maker
Slide wire harness shield off connector
Disconnected harness
Loosened 2 wall screws
Remove old ice maker
Installed new one reversing process

Parts Used:

Refrigerator Ice Maker Assembly

John from PHOENIX, AZ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench set

5 of 5 people found this instruction helpful.

Was this instruction helpful to you?

A glass insert/shelf broke when were cleaning it.

It was very simple-it is just an insert glass shelf above the vegetable drawers. But, it was fairly easy to identify on your website and delivered in about two days.

Parts Used: