FFEF4015LWB Frigidaire Range - Instructions

unscrew the sensor inside the oven; took off the back of range to access harness of sensor; the replacement part harness did not match up to the original, so we stripped the clip from the end of the part and also the end of the harness in should clip into. after joining the wires together with ceramic wire nuts we tested the oven to make sure all worked AND IT DID!

Very easy just had to pull the wire up that holds it secure.

Extremely easy. Two screws and electric connection that had easy pop on-off connection.

All you do it unplug the old one and plug in the new one.

There is an installation video , but it was so easy, and if you clean your drip pans from those inevitable spills you can do this. I have zero mechanical abilities and I did. The website makes it easy to find your part, and the original literature you got with your appliance will direct you where to find the Model # and serial # on your Frigidaire Range. Order your part on line, get it in the mail and insert the Element yourself.Very happy with my transaction.

Pulled out the old drip bowls and replaced with the new. A simple snap!

Followed instructions on website. Went perfectly.

After the smoke cleared and things cooled off, I switched off the circuit breaker for the stove and unplugged it. Then I used a Phillips head screwdriver to remove the to pack panel on the range. Then saw the circuit board that was damaged--all other wiring was in great shape and unaffected. Removed 5 stab connector wires from board after taking a photo of the colored wires and where each was connected (also marked on piece of paper color/position of each wire), and a plug in pin connector. Then unscrewed the electronic circuit board from the range front panel by removing 4 of the same type Phillips head screws that secured it. Luckily, found PartSelect website, who had the original OEM circuit board with the original white overlay that sticks to the front of the circuit board. Ordered the board after speaking to a customer service rep from PartSelect (who was very patient and helpful with me!), and it arrived in perfect shape and securely packaged in 5 days. Installed the replacement board, attached the wires to the plug in connectors and plugged in the pin connector to the pins on the board. Restored power by turning on circuit breaker and then plugging in the stove. It works perfectly!! Note: I also found a great video online which showed how to remove and replace the board. Also, I looked at circuit boards from other vendors on the internet, but they looked a little 'different' from the original one on the range, and I didn't mind paying a little bit more to get a genuine part that would function perfectly! Will purchase parts from PartSelect in the future. Very helpful customer service staff!

Turn off circuit breaker
Open oven remove two oven racks
Position flash light
Remove two Phillips head screws that hold the element in place
Gently slide out element until you locate the two small wires
Gently Detach the two small wires from the back of the burned out element
Position the new element in the bottom of the oven and attach the two small wires to the back of the new element
Gently slide the element back in place and replace the two Phillips screws that hold the element in place
Make certain the new element is lying flat on the bottom of the oven
Replace the two oven racks
Turn on the circuit breakers and test the oven

Unplug the oven (very important). Unscrew the bad element and screw in the new one. Plug oven back in.

Replace the electronic control board & overlay. Tested, works great!

I followed the instructions from the lady taking my order she talked me through the steps

It was simple.............the range-top tilts up so I proped it with a stick of wood, pulled out the old burner and plugged in the new one (when I saw how inexpensive the new element was I orderd two to replace the other 8" because it didn't look long for this world either). The whole operation took less than 10 min. no tools or batteries required!!!!!!!!!.........no-mus-no -fus.

Your prices were the lowest I found on-line, keep up the great work!!!!!!!!!

Just replace the parts. Too easy for an old man.

1. Loosened 2 sensor mounting screws and removed them. 2. Tripped range circuit breaker to off. 3. Pulled out the range but left gas connected. 4. Loosened the 4 screws on RH side of the top back panel and carefully pried that side of the panel open. 5. Using fingers, threaded the sensor's wiring harness through insulation and into the oven. 6. Unplugged old probe. 7. plugged in new probe. 8. tugged wiring harness back through insulation behind the oven. 9. Using 2 screws removed in 1 above, mounted new sensor. 10. Repositioned top back panel and fastened it in place. 11. Shoved range back in. 12. Tripped range circuit breaker to on. 13. Reset clock. 14. Set oven to 450 for test tun. 15.