FEF368CASB Frigidaire Range - Instructions

shut off power to stove. Opened the oven door, removed the racks. removed 2 screws holding the element in place. gently pulled element out to expose connections. removed connections. discard old element. reattach connections to new element and reinstall. very simple.

First I unplugged the stove, and removed the upper-back panel. Then I pulled off the control knob. Then I removed the two screws holding the switch to the stove. Then one-by-one I removed the wires from the old switch and connected them to the corresponding tabs on the new switch. Then, using the knob adapter supplied with the new switch, I figured out how much of the knob shaft I had to remove from the new switch to position the knob the correct distance from the face of the stove. Then I tested the switch with a voltmeter as instructed, and then I hooked up the last wire.
Partselect.com is an awsome website!!! I was able to review comments form other do-it-yourselfers that had similar problems. Then I looked up the Partselect schematic drawings of my stove and was easily able to find and order the part I needed. The part arrived at my house within a couple of days and I had the stove fixed in no time.

The old element burnt a hole in itself and just glowed in an area about the size of a quarter. I unplugged the oven, removed the two screws that held the element and removed it. I plugged the oven back in so we could use the top burners. When I went to install the new element I did not unplug the oven as the controls were off. I did not know the element was hot from the outlet (by design) so when I tried to attach the new element sparks flew and it welded itself to the wire so I jerked it looose. I then unplugged the oven, replaced a blown fuse, and installed the element.

Removed the one remaining drawer guide and stared at it for 10 minutes trying to understand where it came from and how it worked. Looked it up on partselect.com. While there was no part number, the detailed photo on your web site was enought to assure me that you had the correct part. Ordered them in a few moments and three days later I had the parts. The hardest part of the job was trying to understand how to install the widgets. After 20 minutes to crawling around in the stove's inards, I finally got the "aha" and the drawer on this antique stove was finished. Thanks! Couldn't have done it without you.

I first turned the power supply off to my oven. Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the ends. After that I connected the new element to the wires on my oven and secured the element with the two screws and turned the power back on. I pushed the oven-on button and now I'm back in business.

Slide out the old; slide in the new!

Very important first step: Turn off the circuit breaker for the range or disconnect the power cord.
I removed the oven door to make it easier to access the back of the oven; remove two screws and the door lifts off of the brackets. Removed a screw from the top of the oven that secures one end of a wire that supports the broil element. Removed two screws that secure the broil element plate to the back of the oven. Pulled the element forward exposing the end terminals and wires. The wires are connected to the element by spade connectors. Used long nosed pliers to remove the connectors from the element. Pushed the connectors on to the new element and stuffed the ends of the element and wires back through the opening and the insulation. Reinstalled the two screws holding the element in place and the screw holding the wire in place across the top of the oven. Reinstalled the door. Took less than 30 minutes.

It was great. We ordered the part, it was shipped the next day and I had it the day after that. It was easy to install and the stove has worked perfect since. Color us happy!

I removed the back panel, about 6 screws, then found the probe which was attached by 2 screws. Unscrewed them and unplugged it. Plugged the new one in and replaced all the screws. The oven works like a charm now! No more F3 errors!

Removed screws. Unplugged temp sensor. Put screws back in. So easy a caveman could do it.

New part arrived, opened pkg. , Pulled drawer out. . . Snapped in new parts. . . . Done!! Saved myself $100. 00.

When I found the part I needed there was an instructional video on how to remove broken bake element and install new bake element. This was the best video short and sweet and anyone...I mean ANYONE could do it!

Step 1- cut off the power supply (I flipped by breaker, but you could just unplug the oven)
Step 2- remove baking racks
Step 3- unscrew the little metal plates inside the oven where the bake element meets the back of the oven (reserve screws for new element)
Step 4- carefully pull the bake element out until you have the wires through the holes
Step 5- carefully pull the bake element from the wire clips on both sides
Step 6- take broken element out of over and put new one in
Step 7- slide new bake element ends onto wire clips
Step 8- slide new bake element and connected wires back though back of oven
Step 9- used saved screws to screw metal plates on bake element to the back of the oven
Step 10- replace oven racks
Step 11- restore power to range
Step 12- enjoy a working oven and feel like an absolute PRO for fixing it yourself!!!!

Turn off the electricity
Remove knob
Unscrew old switch
Lift stovetop & prop
Remove wires from switch
Remove switch
Plug wires onto new switch
Put new switch in place
Shut stovetop
Screw new switch in place
Trim knob post
Put adapter on post
Put knob back on
Turn electricity back on
Cook dinner :)

Removed old elements I stalled new ones

I looked up the error code on line and found it was likely a faulty oven temp sensor. I was able to find the part and diagram at partselect.com and placed an order. The probe was in stock and arrived within a couple days. The repair took only about 20 minutes and works fine now. Thanks for your help partselect.com!
Jim