FDR251RJS0 Frigidaire Dishwasher - Instructions

removed two screws the disconnected the two hoses (after shutting the water off of course). It was easy.
Unfortunatley the water warped the wood under the vinyl flooring which is new and I really love. I would suggest that a rubber or some type of water proof material be placed under the dishwasher so that if it leaks it won't get at the subflooring. If this had been the case I would have noticed the leak right away.

Removed two screws on each side, lower half. Inside, removed six screws. Replaced the assembly and replaced all screws.
Not worth the fifty dollars for the part, just to have a door open at the right time to empty soap. Quite a hefty price to pay considering the price of the machine

replacing 2 wheels was a breeze. did not need the screws afterall.

remove center nut retaining the arm to the unit and replaced the arm.
replaced the nut.
complete.

The spray arm had become damaged on one side -- one side had apparently melted off. I replaced it, and it seems to have fixed the problem for now.

The new roller just snapped in place.

Very easy to remove old broken door latch assembly, easier to install replacement. With door fully opened, I removed the 8 screws holding down the whole front casing, including the controls casing. Removed 2 Torx screws holding door latch assembly and then made sure that I marked all 4 wires before disconnecting them from door latch assembly. Connected wires to new door latch assembly, secured it with the 2 Torx screws, aligned and secured the controls and front cover casings with 8 screws. Done within 30 mins. Thanks guys for posting how-tos and thanks to PartSelect for a very fast shipping!!!

First dissconnect power, and remove the 6 phillips-head screws from the back/upper side of the door, next remove the 2 torx screws holding the handle assembly, and unplug the 2 micro switches attached to the handle. Reverse this procedure and you're finished. It's so easy, a caveman could do it.

shut off the power on the breaker box, 6 screws inside the door on the tolp and side,pulled 4 wires off, 2 star head screws on the unit. took bad unit off,put new one on and put the screws back in.

5 minutes

Removed the screws that held the cover on, then removed the 2 screws that held the door latch in place. Disconnected the broken door latch and attached the new one. Put all the screws back in and that was it! Also, the shipment of the part was SO QUICK!

First i removed the screws on the back panel, unscrewed the latch, removed the wires and installed the new latch.
I found the latch is too expensive for a little plastic part.

Removed the screws that hold the panel on ( just the top ones-no need to go all the way down the sides. Need a "star" headed screwdriver to remove the switch itself. Then removed the wires (4),one be one, so as not to mix them up. reinstalled all thescres for the switch, then the panel. Job done.
What amazes me is that Frigidaire doesn't read your page to realize that the handle assembly was defective and send out a recall. look at all the repars listed in your site , and these re just from the people that have responded with comments and who use your service. New handle/switch is much more sturdy with a higher density plastic that the original. Your service is easy to use, prompt and accurate. Fixed the dishwasher while my wife went to the store. Dishwasher done in 15 minutes and watched theNCCA tournament for 2hours in complete peace !!!!! No need to tell the wife only spent 15 minutes.

It was a walk in the park. Unscrew the six screws in the back of the panel to reach the latch. Unscrew the two torx screws in the front of the latch and replace each of the cables, one by one, in the new latch in the same order. Put the screws back into place in reverse order and... voila, wthout a single shock !!

Removed the front cover by unscrewing the 8 screws. Removed the latch and attached new one. Re-attached front cover, and it works fine.
The gasket was in fine shape, and I question why I had to purchase the gasket in order to get the latch. Seems crazy and an unecessary expense on my part.

Before starting I disconnected the dishwasher. First I removed the door cover which then exposed the interior part of the door. I then used a star bit on the screwdriver to remove old latch. I disconnected the four wires to the door making sure that I made a point of which wire was connected to what. I then inserted the new latch and reconnected the wiring. Finally, put on the door panel and screwed in the remaining screws. About 15 minutes total work time.