ET1FTEXVQ00 Whirlpool Refrigerator - Instructions

I was about to waste $1000 on buying a Refrigerator. Took 1 mins to search on google "Refrigerator doesn't work". Found a video on youtube, showed a step and step video to solve my problem. Order the part $50 and it took me less then 5 mins to install it. =)

Took out glass shelf to clean. Shelf exploded into a billion little pieces for no apparent reason. Received replacement shelf the next day (with the 3 - 5 day shipping). Cleaned glass, placed in ice box. Viola!

I removed the screw that held the control module in place, then unscrewed & unplugged the circuit board and plugged the new one in. At that point I realized that the mounting bosses on the new piece were a quarter inch longer than the old one and the screws were now too short. The old bosses couldn't be adapted without wrecking them. Luckily I found screws out in the garage that worked. The screws that came with the new piece were the same as the old ones. Also they were packed loose with the circuit board and one was stuck between the protective cover and the pins. Thankfully it fell out on its own before I plugged the refrigerator in.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

I only needed to set the endcap and trim piec es in place, no tools involved

changed the starter connected to the compressor

its not that hard to replace. may need help to tilt fridge on one side so you can get to the bottom to remove wheel.Had to undo all four corner screws/bolts to loosen bottom section and slowly pull out base frame which holds the 4 wheels. this frame is also holding the compressor and fan so be careful.replace wheel and slowly put frame back to position and screw back bolts. pull back fridge to upright position. leave unplugged for a day or two to allow gas to come back to normal level as we had tilted it.plug it back and it works.
thanks
Anoop

The repair was so simple. I removed the old icemaker in about 3 minutes and unpacked and installed the new one is about 10 minutes. It was literally a matter of removing a few screws! Eady to follow instructions!

tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok

took out broken with no tools req replaced new with no tools req

Too simple! I removed the crisper bins, took off the broken crisper cover and replaced with new crisper cover then inserted the bins under it. Viola! Ordering a part from this site was so easy. My frig is 10 years old and I didn't think I would be able to find a part, but it did.

I just removed the old seal cleaned the area and simply installed the new seal. The instructions were easy to follow and project was completed in less than 1 hour.

While cleaning the refrigerator I had taken the bottom glass shelf out to clean it in my sink and unfortunately it broke into thousands of little pieces. After clean up the mess and my cut thumb, I went online to see about replacing it. First went to Whirlpool site, they had the broken shelf but for considerably more than I found on your site. Your website was easy to use and the part and the shipping was much more reasonable. I ordered on a Sat afternoon and the shelf, which was exactly the same as the one that had broken, was on my front porch by Tues @ 9:00 am. You never know when you make a purchase online with a company you are not familiar with, but I can say this was a great experience.

Quoted $275 to fix, paid $65 for the part , Installed the new part in about 15 min. very easy, removed 2 small screws, and plugged in new part.

From the time I started to finish I worked 3 hours, this included installing the new ice maker, cutting into the cold water line in the basement and installing a t with a 6inch piece of pipe with a compression valve to connect to the small cooper tube, this is worth your time to do it this way, its a lot better connection than the small pierce valves that come with the kit, they will leak over time. I installed the filter in the waterline in the basement for easy access