Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Top oven seal sagging, no longer seals
Used 2 side seals to make a new top seal (no longer available). Cut the 2 new side seals to provide about 1/2" less length than the old top seal. Removed one of the end hooks and straightened the hook, removed the old silicone from the hook. Used high temperature silicone and the old hook to splice the cut ends together. Let cure over-night and reinstalled. Works like a champ.
loosened the screw holding the block pulled it out toget to wire cut it about 4 inches long followed the inst.with block kit and it was a breeze. burner working fine now should have did it sooner.
I shut off the breaker checked for power then cut old plugs making sure to allow a little slack. Tightened down wire nuts put on a couple wraps of electrical tape and that was it. Burners work great now I would reccomend this product to anyone with a similar problem.
Move stove away from wall to allow working on back of stove. Unplug stove. Remove metal cover from top rear of stove. Pull control knob off of control (front of stove) Remove 2 screws holding infinite control in place (front of stove) Replacement control not identical to original control, having more terminal lugs and different physical arrangement. I used the terminal letters as a guide for placement of wires. The letters were not exactly the same, but close enough. Re-attach control to stove with 2 screws. Re-attach back metal panel to stove. Shaft on replacement control is smaller diameter and different shape from original, so I removed ribs from inside of control knob hole and then squirted a small amount of hot glue into the hole. Smearing a small amount of cooking oil onto shaft of replacent control I then slid the control knob onto the control shaft, holding it in place until the glue cooled and set. Plug stove back in, and return stove to its position next to the wall.
replace the cook stove's drip bowls instead of cleaning them
I removed the burners and then the older drip bowls of the cook stove--and then I put on the new drip bowls and put back on the burners. My mechanical skills were sufficient for the replacement of the drip bowls.
The surface burner socket that the burner plugs into melted.
Cut the old wires off, removed the screw holding the clamp, installed the new parts. Problems I encountered were the wire nuts. They were too small for the wire gage of the replacement part and the original oven. I had larger wire nuts in my workshop. Also, why so many extra parts like the shrink wrap tubing, two metal clamps to hold the socket, etc.
I needed to replace to two 8* drip bowls on the kitchen range
(a) I took out (and threw away) two stained 8* chrome drip bowls on my kitchen range; (b) ti put in two new 8" chrome drip bowls on my kitchen range. I'm pleased that I was equal to the task.
Removed heating element, installed new drip pan, replaced heating element. Was amazed at fast delivery - ordered in afternoon, arrived fed ex next morning!
one burner that would not heat and others that would not out out much heat
I noticed that one of the burner blocks was completely burned and the others were corroded. I ordered blocks for all four burners. Installation was easy except for one block. The screw holding the bracket to the range top was completely corroded in place. I used a correct size easy-out, which is a left hand tap and drill, to remove the screw. That took about five minutes, including tracking the easy-out down in one of my many toolboxes. The entire replacement of four blocks took about one and a half hours. Stove top cooks like new on all burners! The part kit had all the right parts and they fit like a glove!
The side seals fit perfectly so I just put the hooks in the holes! The top seal was too long so I cut it to size and used super glue which did not hold. Next I looked for a high temp glue with no luck. Finally I put the hook into the seal and used a very fine wire through the holes in the metal of the hook piece and twisted the wire until it held the metal piece in place. Then I installed the top seal and it works fine. There is no longer heat pouring out the top of the oven and my brownies cooked at the right temp for the right time. Hooray!
Burner keep coming on and going off had a short in burner plug-in block.
Turned off stove breaker. Unscrewed burner from stove top, took out burner and spill pan. Lifted top of stove, cut the wire as instructed and put all parts together as instructed. Placed everything back together as instructed. I did it myself!
Ordered wrong part at first caused me to blow out two elements. With the help of PartSelect I was able to get the right surface block terminal and replaced both of them, then found out I had a bad switch, they got the switch within 2 days I had my stove working good again. Thanks to PartSelect. Also watched the video which was very helpful ML