EGR3000EH2CC General Electric Range - Instructions

1) Turn off power at circuit breaker panel
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and discard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!

First I tested oven sensor which checked o k. I then made a diagram of the electrical wireing to the oven control. I disconnected wireing and removed the control then with sharp knife I removed touch control pad. I placed th touch pad on the new panel and installed panel and connected wiring. Pluged into wall rec and test oven which checked o k .

Very easy install of done correctly. When you pull range out,watch the gas line and don't pull it out of it's fittings. Two small Phillips head screws on the front panel low to the sides. Then two 5/16 screws on the top back panel and flip it forward. Rest it on the stove and the control panel is facing you. I'm a 30 year Electrician so please take my advice and make a schematic of the wire colors and the NUMBER associated with that color wire. Once that is done remove all wires and also a green ground wire that is under a screw. The new panel may NOT have the exact same configuration but the NUMBER on the terminals will be the same. Plus all color wires to the appropriate terminals and reinstall !! Great job!!

We had to make sure every bit of broken glass was removed - then removed the outer cover of the door, inserted the new pane of glass, and screwed the cover back on. Over all, pretty easy. (Especially for me!)

Took longer to open the box.

Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.

repair was easy enough, but the kit came with female ends and needed mail ends. I had to splice old connecters to new igniter

Replaced old with new.

Order parts and installed - no tools needed - completed repairs less than 1 minute

Removed old line with wrench and attached new line to gas valve first. Then lowered hood to the stop and attached gas line to burners.........very easy and works fine now.

When turning on the oven, I could see the ignitor red hot but it would not ignite the burner. I ordered the pair of new ignitor and burner tube. Upon removal of the burner tube, I saw a large hole in the tube where the center of the ignitor is located, clearly in need of replacement. Unlike some other ovens, the connector on the new ignitor was the exact fit for my oven (Hotpoint RGB745BEA7WH). After access to the tube, the replacement took less than 10 minutes not including watching about 3 youtube videos on how to actually do the replacement prior. You should turn the gas and electric off but ooops, I forgot. I was shocked at how easy this was!

Unplug the range from its wall socket to avoid electric shock. The various range parts that support a pot or frypan are easily lifted off their perches, exposing the small white igniter. The only moderately difficult aspect is wiggling the igniter out of its retainer. The electric wire leading into it then can be pulled out and fed into the new igniter with a push. Replace igniter in its retainer, then replace the range parts you removed to expose the igniter and plug the range back into the wall socket. Piece of cake.

slid the old ones out and slid the new ones in. done

My son took out the old burner bar and there was a hole burnt right through it. I ordered the part on Weds night and was surprised when we received it so quickly on Fri morning. He had no trouble at all - just removed the old igniter and bar and replaced it with the new one. Nothing needed cut or spliced - perfect match. Now I can bake again!!!

Simple swap and go.Several wires had different locations but every thing was marked well on both panels.Did one wire at a time.Took about 45min from pulling out oven to pushing back in.Just wish I had known about your site years ago.