EG2109 Speed Queen Dryer - Instructions

You have to take apart the whole dryer to get to the belt.Nut driver with cordless drill make it go so much faster.Unplug dry, take apart dryer and replace with olr belt with new belt.Takes about 20 minutes to do.plus I took off the two guide wheels on back of cabinet and greased everything.Works like brand new.I had a repair guy tell me I needed a new motor.If you can spin the drum by hand replace belt first.

I had to punch out the disc on the right side and remove the exaust pipe so I could get my hands in to remove the broken pulley assembly. Then put the new one on tightened the nut and bolt. Put the spring back on and the belt. Added a bit of grease. Put the exhaust back on. Plugged it in and I was done. The most difficult thing was finding the part on my phone screen since my pc is on the fritz. Once I got the proper definition of what I was looking for it was easy.

Removed top and front of dryer. Released drive belt tension. Removed drum. Removed nut on belt tension idler lever/roller and replaced with new unit. Removed and replaced drum rollers. Reassembled dryer. Dried them clothes.

Video online was very instructive...only difference was I unmounted the motor mount plate from the bottom to get to the idler lever easier.

Was very simple after watching the repair video provided o you site. Went exactly as described. Will deffinately use your parts again and will highly recomend it to anyone else who needs parts.

Took front faia off , took off fan duct, then took old drum glides off and put on the new ones. Make sure you buy two, when you order them they only come in single size lot.

as described in video. Very well done. Thank you

remove front door,disconnect plug from motor remove motor assy,replace idler

replace rollers

Lifted the top of the dryer removed two screws and pulled the front of the Dryer forward. Slipped the new belt over the drum and over the motor pulley.
Pushed the front back in place and snapped the top of the dryer down and the job was complete.
I thought the part would take three days to get here.
It was delivered the day after I ordered it.

Parts arrived on time as usual. Disassembled dryer and put all parts on. A small pair of snap ring pliers for rremoving the shaft snap ring and wheel of idler woud be beneficial. I did it by removing the entire idler. Hardest part was getting nut back on idler bolt. Nut goes behind mounting bracket for motor and is blocked by dryer exhaust on one side and frame of dryer on other. Used long reach needle nost to hold nut until bolt started into nut.
Reassembled dryer and ran like brand new... no more squeaky!!

Determined no air flow or heat through system even though dryer spun and timer worked. Ouside vent dispelled no air. Opened dryer panel.
Blower wheel/fan broken off from shaft. Googled appliance parts ... found ... Partselect .... keyed in mfg, model number ... schematics available ... found part ... ordered ... received in two days ... installed ... reassembled. Working fine ! $ 30.00 compared to buying new dryer ! This was a refreshing and rewarding repair. If it could always be this smooth !!! Great resource ... PARTSELECT !

I unplugged the power started taking the housing apart it was all exploratory to me as it has been many years since I worked on one. Pry the top front up with a screw driver remove two screws at the top front and two hold down brackets at the top rear flip the top onto some boxes stacked up in back of the dryer. took digital pictures of 2 sets of wires in the front and disconnected them pulled the front panel up off the 2 holding clips swung it out to the right . Removed the 4 screws holding the hub on and removed it slid the drum off the felt pad ( after I put an arrow on it with a marker) and out of the housing. Now comes my dilemma the idler lever shaft was totally screwed up and the belt was laying on the floor of the dryer housing so I had know reference to how the new one should look or the pattern of the belt. I ordered the new pulley from part select .com but it would not take my credit card so I called their 888 # it turned out their service is out of canada and my card was not good out of the states so I used a different visa I received the part in 1 day however it does not come with any directions so I referred to other repair stories on their website but everyone their had their old ones in tact to refer to. I put it back on as best as I could figure but the belt pattern was my new problem every way I tried the belt was to loose I figured the belt must have streched I measured it and it seemed a little long so I ordered a new one again the part came in 1 day. But again no directions came with it. I went back to the partselect.com hoping to find a diagram but no luck there. I found another website with six diagrams to choose from picked the one that seemed most logically to work. I put it all back together and it works. It makes a repetitive clunking noise like it has a half a pair of sneakers in it but it seems to run alright. Its only 2 years old and my freinds told me buy a Maytag and I won't need the extended warranty Yeah right Live and learn

This would be an easy job, if I were to do it again.

I needed to download a manual only to get ACCESS to the machine. Removing the outside lag bolts did NOT provide access.

They had hidden clips that were ENTIRELY invisible from the outside. I believe this was done deliberately, to prevent those who don't know the specifics about this machine from gaining access.

It's an easy job, once you know the idiosyncracies of the construction of the machine. It's a major pain in the ass if you don't, even if you are used to replacing belts in other dryers.

Having done it once, the next time I could do it in under 20% of the time it took me the first time.

Basically, Followed the instructions in the Video for Belt replacement. I found out however that the Tensioner was also broken aand needed replacement, and this required the snap wring pliers. also spindle on motor was stripped and had to use "lockTite" to repair that. Overall was far better "doining it myself" than paying for repai service which would have cost several hundred $ in costs. This increased my confidence level to know that as long as parts are available I will always be able to repair this appliance!