EG2109 Speed Queen Dryer - Instructions

I had already taken the dryer apart prior to changing the felt seal. Had oiled the rollers, greased the bearings & vacuumed the whole inside of the dryer out. Had used a high temp lubricant on the seal & had stopped squeaking for about a month. I ordered 2 seals & when they arrived, I popped the top of the dryer off using the putty knife to pry the spring latches. I opened the top up & leaned it against a wall. I disconnected the wiring to the light & the switch in the door, making note of the wiring order. Then used a nut driver to take the 2 screws from the inside out, that holds the front cover in place. Then the same for the 4 screws holding the front bulkhead in place. Then lifted up & out from the unit. Then used the putty knife to scrap the adhesive & old seal off the bulkhead. Cleaned as much of the adhesive off, then applied some high temp silicone adhesive to the bulkhead, placed the new seal on, using some clamps to hold it in place. After making sure it had adhered to the seal & bulkhead. Did the reversal of the above mentioned steps. Moved the unit to laundry room, plugged it in then started it & voila no more squeaking dryer.

took frount off ,then filter, pulled drum out, then blower plate & spun impeller off. went back together easy ,except belt . that gave me a little problem but finally got it thanks

Early in the life of my dryer, the Cylinder Seal came out. For the past two years I put off buying the part. When it came in, I p[opped the top of the dryer, removed the two screws holding on the front panel, and pulled the Cylinder of the back wall of the dryer. I then placed the seal in the right spot, glued it down and reassembled. About Fifteen minutes of work and a cheap part, and now my dryer dries a l;oad of clothes in an hour instead of three.

unpluged the dryer,and removed the top.
took the front of the dryer off,release the belt and removed the drum.
unbolted the idler lever.

then I put it back together.
the bolt that holds the idler lever will be a little hard to replace for some.

unplug appliance.removed 2 screws @ the rear of dryer top to tip lid back. unplugged the door switch wires.took out 3 philip screws that hold lint screen to inside of drum.removed 2 screws @ dryer front top. lifted dryer front panel off. the drum was now loose. slipped off old belt - replaced with new. set drum back into place. made sure new belt was on motor pulley & behind tensioner pulley arm. replace & reconnect items in reverse order. plug back in & test. after seeing the wear on the plastic tensioner pulley i regret not ordering that part for replacement also.

remove bottom two screws on lower front panel, remove panel. remove two screws on lower portion of door panel, pull bottom panel towards yourself to release pins at the top. Disconnect wiring for light and door switch (make sure to note what wires go where. Complete removal of front door panel. Remove 4 screws holding cylinder frame in place, lift to remove. remove remnants of old felt seal, use rotary tool to remove excess glue, etc. apply glue (used rubberized gorilla super glue), apply felt seal - allow glue to set up. reinstall in reverse direction from removal. Be sure to use glue as there are no clips or other retaining pieces for the new felt and it will not hold in place. overall pretty easy.

After removing the front panel, the igniter just just snaps into the bracket.

I first unpluged the dryer. Then I
Removed two screws and removed bottom cover, Then removed the door assembly.Here I had to unplug the light and door switches. I then removed the four screws that holds the tub mount in place, Then I removed the eight screws that hold the blower cover in place, then removed the blower. replaced blower and reassembled in reverse. I started the dryer and it worked fine.

The repair looked simple enough until it came time to take the out wheel off. Because you can not hold the motor shaft(and the wheel screws on) it was necessary to remove the whole motor assembly and then grind the out shaft down, then use a small screwdriver to take the remaining shaft off.
I must say it was nice to recieve the part in as fast as I did we live in a very rural area and things like that are very hard to find

Being my lousy Maytag washer died THE PREVIOUS DAY, spewing water, etc. and I had rushed out and bought a new washer, I was determined not to replace the dryer (though I now am a serious NON_FAN of Maytag).

I disassembled the whole dryer and finally got to the blower wheel which was broken lose from the molded nut. I supposed something like a dime or penny got in there to shred it.

PartSelect's website allowed me to find the part in 5 minutes. It was on my doorstep the next afternoon.

Installation was straightforward BECAUSE I stacked all the screws and and labeled them appropriately. It took about 30 minutes to reassemble and the toughest bit was getting the drum in with the belt positioned properly.

Super easy. 2 screws allows you to remove the access panel. One screw on the igniter bracket removes the igniter. Pull off the 2 wire connectors and plug into the new one. Test the dryer and close the access panel.

My son will discribe how he did the repair.
First I opened the top, then I removed the front with a 1/4 inch ratchet and socket. I took the cover off the blower housing with a nut driver. Used the appropriate socket and a 1/2 inch ratchet, and an adjustable wrench to hold the motor shaft and removed the Blower wheel. I replaced the broken Blower Wheel and put all it back together.
Our dryer is now working great and there are no unwanted sounds emanating from within. We are very happy with PartSelects promptness and that we recieved the correct part as ordered. PartSelect website was easy to navigate. We plan if the need arises to do so again in the future.
Thankyou Frank and Rodney

Very simple repair. Remove front panel, door, drum etc. Try to keep everything seperated, screws etc. I put lockjaws on the back to get the nut off the front. Make sure to check the housing for "melted on" blower wheel residue. Easy enough to remove. I checked with my local parts dealer he wanted twice the price and needed to order it (at least a days wait). PartSelect sent the exact same part in a day and a half. Put everything back the same way I removed. Hardest part is the drum and belt. While you have everything apart don't forget to clean the thermastats etc. PartsSelect was quicker and cheaper.

Removed two screws on lower front dryer panel with 5/16" socket and wrench. Removed three screws and plastic filter dryer screen vent with 1/4" socket allowing easy access to upper limit thermostat switch located on side of igniter flame assembly tunnel. Removed two screws attaching limit switch and disconnected two wires. Replaced with new limit switch and reconnected wires. Reassembled dryer. Works fine. Drying time for regular items such as towels is now less than 1 hour.

Make sure to unplug the power cord.Pry the front,top of the dryer up with a screw driver. Carefully disconnect 3 wires and remember where they go, top right. Remove 1 top bolt on each side of the front cover, inside.Pull up slightly and towards towards you to remove the front cover. Disconnect the light wires if applicable and remember where they go from the front drum support. Remove 4 bolts on the front drum mount cover; the lint catcher will come off with it. If needed, pull up and towards you on the drum to lower the it off of the guide rollers to allow slack in the belt. Reach under the drum, raise the idler lever, slide belt from under the idler lever pulley, remove the belt from the the motor shaft. Carefully remove the drum. A 7/16 wrench and ratchet can be used to remove the idler lever from the mount. Remove idler lever from the spring. Reverse these steps for installation of the new idler lever. For installing the belt, actually fold the belt and put it under the idler pulley and back onto the motor shaft. The idler lever should sit on top of the belt when on properly. Make sure the belt is lined with the wear area of the dryer drum. Roll the drum manually, counter clockwise several times to help insure belt alignment before reconnecting the wires and re-installing the front cover and top. A belt replacement will not require removal of the drum.