ED5FVGXWS00 Whirlpool Refrigerator - Instructions

Be advised that to do this job, you have to take the ice tray and feeder assembly completely apart. The only tricky part is that the nut, part 31 in the drawing, that holds everything together is reverse threaded. Since it's plastic, you're afraid you'll break it. If you know it's reverse threaded to begin with you can go ahead and apply the required force to get it off.

I had falsely assumed that the ice maker control module was the problem, so I ordered a new one and replaced it. Still no ice. Upon closer examination of the whole unit, I noticed the heating element had a corroded spot, and checked it with a continuity tester, and found it was bad. I ordered a new complete ice maker unit, and it was actually easier to replace the whole unit rather than just the control module, and only cost about $20 more. I was able to return the control module for a full refund. I would highly recommend replacing the whole ice maker if it is not working, rather than just the control module. It is also handy to know that there are little "ports" on the control module for testing all the functions with a multi-tester. One for the motor marked with an "M", "T" for thermostat, "H" for heater, "N" for neutral. Had I known all this from the start, it would have saved me a lot of time and trouble replacing the wrong part!

After watching the instr. film I found it very easy to do.
This is what motivated me to do the job and save a LOT of money. It was actually the second repair I did.

First I installed a defrost timer, (the old timer had burnt out contacts in it) It seemed to work for a few days, then went back to not comng out of defrost cycle, I then installed a defrost thermostat. It seems to be working better than before. I found out that maybe I wasn't running it cold enough. So I turned it up colder. Now it works ok for 2 - 3 days, then I check the Temp in the freezer and its up to 6o. So I manually reset the timer and it works for 2 - 3 days. Don't know what to do now to fix it.

I removed the glides under the edges of the meat pan, remove the old pan, put the new pan in and replaced the glides. I was very pleased with PartSelect. I ordered my part, and it arrived the very next day. I will definitely order my next replacement part thru PartSelect.

pull the fridge out away from the wall and hope you have a long flex water supply hose.remove cardboard cover,oh yea unplug fridge first.unplug wire from the relay.flip the wire retainer off the relay and pry it away from the compressor.pull the 2 prong capacitor off and then reverse the steps to reasemble. skip the middle man at the local appliance shop.i waited 2 weeks for him to get the part and gave up.your reg shipping got it here in 2 days.

Mine is a simple tale of the missing ice cube dispensor guide. When we moved, the guide was missing so when I built our new home with a kitchen in the basement I wanted to hook up the ice dispensor but when I did, the ice cubes always fell off to one side. I decided to order the misssing part on-line. I ordered it paid for it and then received it the next day-wonderful. Within ten minutes, I was ready to go. Thanks for great service. Rick Davis, Bloomington, IL.

Turn off water supply too ice maker and unplug the fridge power. using a nut driver remove one bottom screw from the bottom, near the front. The other two from the side atop the ice mold. (loosen screws and ice maker will lift up and off.)
I set the ice maker on the counter, snapped of the front cover by hand. using a phillips driver, remove two screws near the bottom corners.(they go through the circuit board into the ice mold)
circuit board in one hand, other end of ice mold in the other, slowly pull apart about 1 inch. remove the silver colored "on, off" bar at the end by snapping the retainer out of the ice mold. (the silver bar stays with the circuit board end)
Watch how the ice guide(white fingers stationary on side of ice mold) hooks too the ice mold on each end. swap ice guide to new ice mold, insert three guide pins on end into holes on the circuit board, while holding ice guide onto ice mold, watch rotation bar while inserting into motor.(it only splines one way.) when each piece is lined up, simply push together and reinstall two screws. snap circuit board cover into place. reinstall ice maker into freezer in reverse order.

After removing a few screws to get to the drum my husband had it back to working like a charm.This part seems to be better made than the original part in the refrigerator.

simply slid out old damaged/taped up shelves and slid in the new ones i ordered,

Removed the three motor screws pulled off old motor put new motor in place replaced screws and re-installed. It was producing ice three hours later. I originally tried to obtian these parts directly from Whirlpool in which twice they shipped me the wrong parts. Finally gave up on them and entered the whilrpool part number which crossreferenced to new part number which was correct the first try. Thank you!

This company is WONDERFUL! I ordered the wrong drawer the first time, but their return process was a snap and the correct drawer arrived the next day. It's great to know that there is someone out there with just about every part you'll need for about any appliance that is truly customer friendly.

Excellent fit and installation. The door bins slid right in and created the extra space needed on the shelves.

That was due to the evaporator blocked by the ice. Check found the defrost timer is okay. The next thing I can think of is to replace the Electronic Control Board which is installed in the fridge side top compartment. Ply open the face cover, remove the nut and screw that secure the EC Board. Pull out the cable, mount the new card and re-connect. So simple. It is back in order.

Watched the website repair & adjustment video, ordered the part which was exactly like the one currently in the fridge. Took only 10 min. to install. Then, 2 hours later we had ice! And still have ice on a consitent basis. Easy fix, life's good!