ECKMF284 Whirlpool Ice Maker - Instructions

turned water off to ice maker unpluged fridg while doing repair which was such short time everything was ok removed 3 1/4 hex screws holding ice maker in position while holding ice maker in hand unpluged wiring connection for it removed old ice mold which coating had come off of which was very simple 2 philips screws which are recessed on control unit then gently wiggle assembly apart paying attention to how all the tray parts went together then reinstalling same way as they were remove very simple repair anyone should be able to do

Watched a video on YouTube on how to replace the icemaker control assembly. The video showed unplugging power, turning off the water supply, and removing the entire ice maker from the freezer. After watching the video several times, I unplugged the refrigerator but did not turn off the water supply. I did not remover the entire ice maker from the freezer, but I did remove the wire shut-off arm. After that, I pried off front cover of the control assembly. The control assembly is held in place by 3 Phillips screws; I removed the screws, removed the icemaker control assembly, replaced the assembly with the new one, replace the cover and wire shut-off arm, and plugged the refrigerator back into the wall. Had ice in about an hour (seemed the system had a little delay before deciding to go to work!).

Easy, just removed the ice dispenser and the left support for the dispenser so I could get to the bottom screw easier. Three screws held the mold in place. The bottom screw had to be removed completely, but I just loosened the two top screws and lifted the mold out away from the wall and then disconnected the wiring. The end cover snapped of easy with a screw driver. I then removed the three screws holding the motor. then pulled the motor off.(the next square part under the cover. I did this before I realized that I could use a small screw driver and stick it into the holes to remove the mold and not mess with the outer screws. After I removed the mold, I replaced the new mold into position, without putting the white forky looking part back on so I had to take the two screws out and put the part in place before attaching the motor back to the mold. Everything went back together just like a charm. The ice maker is working good, easy job. Gone golfing now.

3 Years ago our icemaker stopped working and we paid a professional $225.00 to come and repair. This time I chose to investigate the problem on line and PartSelect website gave me info on the motor assembly that may be the problem. Sure enough I purchased the part, it was delivered in two days. My husband installed the control & motor assembly in less than 15 minutes. We had ice within hours. Thanks for saving us a service call and the expense. The Goldbergs

removed icemaker timer/controler replaced with new part.reinstaled it works perfectly

Removed the two screws holding the funnel in place...removed the old one and replaced it witht he new tubing...screwed screws back in and the jov was complete. It actually took longer to get it out of the sack than it did to put it together

Turn off water, removed two mounting screws, unplugged solenoid, removed incoming water connection and plastic pipe to ice maker. Installed new valve, connected water lines, reconnected plug, remounted with screws. Turned water back on, over rode power to ice maker and checked for leaks. Total time about 5 minutes. Very easy repair.

unpluged the refrigerator, remove three screws holding ice maker in place, disconnected wire clip, removed front of icemaker by relaesing two clips holding it in place. the module and motor assembly are held in place with three screws. put the icemaker together and replaced it in freezer, and pluged the cord back in. the icemaker started making ice in about 15 minutes. very easy fix

I took the front panel off the ice maker. Found the contacts on control board were burnt. I called Partselect, told them my model # and they directed me to a new control panel. 4 screws later I had part back on and ice makin.
Thanks Partselect!

John Long

Removed icemaker by first removing the nutscrew that holds the cover to the electrical connection in place. Next, I removed the door then slid the icemaker out and diconnected the electrical connector. With the icemaker out, I R&R'ed the motor assy , reconnected the electrical, and slid the icemaker back in place. Next, I replaced the door, turned the icemaker switch on and waited. In about 30 minutes I heard the water being injected into the icemaker, and soon there was ice. The repair was easy and inexpensive. Tx to Partselect which I found on Google.

It took both me and my wife! One of the new parts we recieved was broke so we took the part off of the one that didn't work.

Unplug the fridge. Used the screw driver to remove the motor. Easy. Now putting the new one in was difficult because it has to line up exactly.
Thats what took 15 minutes but after me and my wife worked on it, we had a bucket of ice by morning!
We only knew how to do what we did because of reading these messages on this site. It came with no directions.

There was three screws to remove to unmout the ice maker, and unplug the wire harness,then two to remove to slip in new stripper. All took about 20 mins.

After removing the ice maker, I guessed that the moter could be the problem,bought new part I installed it and held my breath.thankfully that was it.thanks to parts select I saved a lot of money doing it myself.

Removed 4 screws, pulled unit out of slots, unpluged control wires plug and removed from fridg. Removed 3 screws that hold the motor module to unit. Then reversed procedure and had the batch of ice cubes one hour and fifteen minutes from the time I started replacement.

removed front cover installed gearbox then attached lift arm plugged in frig turned on h2o and now i have plenty of ice ! ordered part on Saturday got part on monday in the mail and had ice by supper what a great place to shop and the service was great and parts made easy to find on the website. thank you very much! I will refer your business to all my friends.