All Installation Instructions for Frigidaire Refrigerator E23BC79SPS3

GASKET WORN AND LEAKING

SIMPLY REMOVE THE OLD GASKET PULLING LIGHTLY BY HAND
THEN PUSHING THE NEW GASKET BY HAND

Parts Used:

GASKET-DR,MAGNETIC FF GREY 36

Dennis from Lancaster, SC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

One blade broke from condenser fan

The part i recieved, from parts select was a larger in circumfrence (<1/4) than the original. However i was not aware of this until after i treid to repair it.

I removed the broken fan from the condenser. This was very sipmle.

When i pluged the refridgerator back in to the outlet the fan tried to start up but soon began to make aloud noise, due to there not being enough clerance.

Parts Used:

Condenser Fan Blade

Chris from Lockport, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

12 of 32 people found this instruction helpful.

Was this instruction helpful to you?

Thin, flexible edge on outermost door gasket was tearing from the main gasket, likely due to being rubbed when accessing refrigerator..

Gasket is held in place by an extrusion on the back side. Simply remove the old gasket and press the new gasket's extrusion into the track on the door.

Parts Used:

GASKET-DR,MAGNETIC FF GREY 36

Dennis from Oley, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Previous seal had a tear and cold air was leaking around seal

Pulled the old seal out of the groove. Placed new seal in the groove. New seal has to be heated and massaged to get it into proper form so it does not leak. I have been continuously heating and massaging to get the seal to get it in the proper form. Been working on it for a week. Almost there.

Parts Used:

GASKET,FREEZER DRAWER,GREY

Daniel from Hampton, NH
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

There is no power, due to the COVID-19 pandemic there no Tech support available,

My repair plan is to continue buying parts for it until is starts working. I notices a large rusty stain on the back of the refrigerator, so I replaced the Ice Maker. Then, I replaced the Evaporator Motor. Yet nothing will come on.
I called Conn's Home Plus where I bought the Frigidaire Refigerator back in February 2014. The Tech said that It needs a Board-main Power (computer part). So I it ordered from PartSelect. It is due here by July 20, 2020. The Parts and Tech cost is now over Five Hundred ($500) dollars.
HELP!! I need INSTRUCTIONS, HELP!!!
Albert F. Alfaro in San Antonio, TX.

Parts Used:

Ice Maker Assembly

Albert from SAN ANTONIO, TX
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Screw drivers, Socket set

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

ice maker is stuck on crushed ice.

We had someone to come and look at it and we were told it was the solenoid valve. The repairman unstuck it for us and said when it does it again, he would have to order the part. We took it upon ourselves to order the part and DIY. We replaced the part that we were told was the problem and "guess what" it's still not fixed. It's still shooting out crushed ice. Will have to call repair guy back out here to see what we did wrong.

Parts Used:

Refrigerator Ice Dispenser Solenoid

Mary from MAGNOLIA, AR
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Screw drivers

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

THE GASKET LOCKING INSERT DID NOT FIT THE BOTTOM OF THE DOOR.

I REMOVED THE OLD GASKET BEING VERY CAREFUL TO SEE EXACTLY HOW IT CAME OFF. I INSERTED THE LOCKING INSERT INTO THE TRACK IN THE DOOR WHICH DID NOT FIT AS THE OLD ONE DID. AFTER USING TREMENDOUS FORCE WITH MULTIPLE TOOLS I DID MANAGE TO GET THE TOP AND THE SIDES TO LOCK INTO PLACE AND EVENTUALLY HOLD. THE BOTTOM OF THE GASKET DID NOT HOLD SO I USED CLEAR CAULK AND TAPE TO HOLD THE GASKET IN UNTIL THE CAULK CURED. AFTER THE CAULK CURED THE GASKET HAS, SO FAR, REMAINED TIGHT.

Parts Used:

GASKET,FREEZER DRAWER,GREY

Robert from Lexington, SC
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

routine maintenance

slide old filter out and insert new one

Parts Used:

Air Filter

fred from Austin, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Slide assembly broke on left side of freezer drawer.

Took front of door off, took out freezer basket removed one screw, took off old part and put on new part, put everything back together and it was done. 15 minutes done.

Parts Used:

Lower Freezer Basket Slide Rail

Garry from FREE SOIL, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Broken built in bin hanger

Lift broken bin out and place new bin in place push down to make secure fit.

Parts Used:

Gallon Door Bin

Charles from REINHOLDS, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Refrigerator water dusoeswr stopped working

I removed the defective water valve. All wiring and tubing connectios were color coded.
It connected the water tubes and electric plugs to new water valve.
The water dispenser worked perfectly after I reconnected everything.

Parts Used:

Water Inlet Valve - 4 Coil

Dean from Pawleys island, SC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Wrench (Adjustable)

1 person found this instruction helpful.

Was this instruction helpful to you?

Original ice maker not working leaking water water out door

Removed exterior housing, sliding old unit forward to release. New unit went in easily. Caution wires don't get pinched.

Parts Used:

Ice Maker Assembly

Michael from FREE SOIL, MI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

Ice Maker was making ice erratically

After sending PartSelect the info to their troubleshooting dept. about my ice maker, they recommended replacing the ice solenoid. I did so at a cost of $102. No change, turned out replacing the ice maker(did not purchase from PartsSelect) was the issue and works fine now.

So wasted $102. FYI the part took 6 days to arrive.

Parts Used:

Refrigerator Ice Dispenser Solenoid

Daune from OCALA, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

A set scew was ordered twice.

The first order arrived in a huge box and there was no scew to be found, the box had wholes in it. I was given a refund and told to order again.

The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.

Parts Used:

Screw

Susan from BRAINTREE, VT
Difficulty Level:
Very Difficult
Total Repair Time:
1- 2 hours

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

ICE WOULDN'T DISPENSE FROM ICE BOX

I read other suggestions trying isolate auger motor shaft with pliers while turning bar drive. needle nose pliers could hold the shaft. bar drive just would spin. so took the whole ice box assembly out
(only 2 screws) and with a metal cutting blade used the sawzall to cut along the shaft. freed it up enough to then unscrew it from that point. Left handed threads by the way.

Parts Used: