DW524L1ASS0 Whirlpool Dishwasher - Instructions

Looked at other side of top rack which still had the stop. Just had to orient the direction of the stop and push it firmly onto the rack arm. Took a couple tries, but it went in and locked. Works perfectly. Inexpensive and easy fix to to very annoying problem.

Unplug dishwasher and slide it out from under cabinet. Remove old broken link (a heavy string between two plastic parts) and replace with new one. Slide dishwasher back and plug it in. Very easy and no tools required.

The video included with this part is perfect. Unplug the dishwasher, take off the front trim piece, remove the drain hose from the pump, unclip the power, press the little clip that holds the pump in while turning it counter clockwise to remove. Then just do that in the opposite order to put the new one in. Just make sure you hear it click when you twist the new one on so you know the clip has engaged. Super easy.

Soak up the water in the dishwasher with an old towel. Removed the cover under the dishwasher. Found the pump and twisted it off anti clockwise. Replaced with the new pump. Run a quick cycle, to make sure it pumped out all the water. My wife has used it several times since without any issues.

I removed the old seal and carefully cleaned the track into which the seal was fixed. No tools other than some ordinary cleaning liquid, cloth and small wooden piece to swab out the track. Easy and quick. As a note here, I first used the incorrect schematic for the unit and ordered the wrong seal. However after receiving the wrong part, I made the correction and reordered. I did this over the phone as I needed instructions to return the part. The person taking my order and answering my questions was very helpful and I want to take this opportunity to thank her.

I am a 61 year old woman and it took me a total of 2 min. max. Popped it into place and pushed in button that holds it..Taa Daa...perfect!

Tried to clean old part and it did not work. Ordered the new part on Saturday and received it on Tuesday. Removed the old part and installed the new one. Ran the machine and it worked great. A big savings on not having to buy a new machine!!

The old tine row came out easily and the new one was easy to pop into place. I was pleased that it was so easy to order a replacement part.

I did not relize that the drain hose was in two parts. Naturally I ordered the wrong half. So after I relized my mistake, I re-ordered the correct part. Once the correct part was received the repair was easy and went well.

1) clear out the dishwasher
2) remove unit securing screws from top or sides of DW and cabinetry near the top or under the counter top
3) gently pull the dishwasher from the cabinetry about 20" is plenty, mind the connecting hoses and electrical connection
4) close the door! pull back the insulation from the area of the hinge and photograph both sides - this will save you the pain of going online
5) you will see the cord, the tensioning wheel assembly and the door balance spring on both sides
6) with the door closed to relieve tension on the cord, remove the cord from the balance spring - this can be done w/o tools at this point
7) remove the 5/16" screw from the plastic tensioning wheels and remove the tensioners, cord - leave the springs in place if not replacing them
8) install the door end of the cord to its hook on the hinge, install the new tensioning wheel assembly, install the old 5/16" self tapping screw through the lower wheel and into the outer hole in the frame
9) thread the cord from the door over the upper wheel and lower wheel. the lower wheel has cord retaining tabs to hold the cord on the assembly
10) hook the eye end of the cord to the balance spring and you are finished with the first side - repeat operations for the other side, reposition the insulation and slide the washer back in its cavity - do not forget to reinstall the stabilizing screws in the upper washer frame
11) you've done it!
12) have a cuppa and do your second washer that hasn't failed yet - it will soon.

Watch your video about my dishwasher symptoms. Move water tube for upper rack to the right and release lower spray arm. Remove 4 clutch head screws from filter cover and remove. Dig out 10 years of undisolved soap and reassemble.

I am NOT an appliance technician. I am simply a somewhat handy homeowner. Removal of outer door panel requires removal of two screws from inside the top of the door assembly at the latch, as well as all of the obvious mating screws from around the perimeter of the inside of the door assembly. Use a #15 torx driver bit. Pull top of panel out (away from the machine) by maybe two inches, then lift the outer panel up to clear the bottom end of it from the lower positioning brackets. DO NOT lever the top of the panel outward. Keep it close to the inner door. It may take bit of an upward tug to dislodge. Careful here - the outer panel will simply fall free. Two wire pigtails that are connected to components on the inner door are short, so be careful not to strain them after dislodging the outer panel. One is connected to the dispenser. Disconnect both as to provide good clearance for the component replacement. The main wire harness is of sufficient length as to not cause a problem. The six 3/16 hex head screws holding the dispenser in place are easy to remove. There are two small sheet metal tabs that keep the device in place after the screws are removed, but a rectangular mounting frame or bezel will come off, along with the little black curtain that protects the unit. The tabs are at upper left and lower right at the perimeter of the opening in the inner panel. They must be levered gently as to allow the dispenser to push inward for removal. After removal, spend some time cleaning the inner surface of the inner panel as to ensure that the new device will make a watertight contact when fastened in place. Bend the tabs slightly back to an inward position, and install the new dispenser with the socket and motor to your left as you look at it from outside the machine. It clicks in to place and stays put. The bezel mounts only one way (in terms of being upside down) and the flat surface must be toward the inner door. Re-positioning the little black curtain is tricky but if you follow the marks in the material from the previous mount it should work out OK. Tighten the screws evenly as to ensure a good seal. Move the outer cover closer and reconnect the two plugs. Use an object to wedge the inner door open by a few inches, and lift the front panel such that you can position it and slide it back down on the inner panel as to re-engage the lower holding brackets. This keeps the bottom of the panel in place during the reassembly. Now for the fun part... The upper end of the outer panel has to be positioned just right against the inner panel in order to seat the two long screws that straddle the latch assembly from the inside. You'll need clamps, or two people. There's a flat rubber seal on the top edge of the inner door. See that it is seated properly, and then that it becomes covered by the outer panel. If one person firmly holds the panels precisely in position, then the other person can install the screws to a point of being mildly snug. The other two longer screws go in the top-most holes at the upper/outer corners of the door assembly. Place them next. From there, you can carefully replace all the rest of the screws. Only after all of the screws are in place should you make all of them tight. You're done.

Removed required hardware and dishwasher from undercounter mount. Turned dishwasher on its front and removed the old motor. Installed the new motor and tested for function. Installed once test was successful.

Remove 2 screws on lower baseplate. Remove 2 screws that hold dishwasher inside cabinet( may be attached to counter top or side cabinets). Turn off water supply to dishwasher. Remove any connections such as water supply, electrical connection, or waste water line that prevent dishwasher from being pulled out about 3/4 of the way. With the dishwasher door closed, remove broken parts and replace with new parts. Pull on spring to make final connection of nylon cable. Reverse the above instructions for re-installing the machine.

I took the unit apart to find out what was making the loud noise and found the seal on the main pump had been leaking ito the bearing on the motor.