DU910PWKB0 Whirlpool Dishwasher - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The soap dispenser lid was broken
I ordered a dishwasher soap dispenser "lid assembly". When it arrived, it was not an assembly at all but only a lid. I had to reorder a pin and spring, When i finally had every thing, it was an easy repair.
Parts Used:
-
ed from potomac, MD
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
4 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dish washer leaking
Pulled the old gasket out with needle nose pliers, cleaned the slot for the gasket, installed the new gasket, needed no tools. This repair took 5 min.
Parts Used:
-
Gary from Winnemucca, NV
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
SOAP DISPENSER DOOR DID NOT CLOSE.
WATCHED THE VIDEO FOR 2 MINUTES. REPLACED THE 3 PARTS IN LESS THAN A MINUTE. THANKS FOR THE VIDEOS.
Parts Used:
-
ROBERT from MAHWAH, NJ
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
4 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
A spring was broken in the disposal chopper
I bought the kit because it had other parts that I thought I needed.
Parts Used:
-
Robert from Sherwood, OR
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken door spring
Pulled dishwasher out from counter. Took cover off and replaced door springs.
Parts Used:
-
David from LEONARDTOWN, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
1/4 inch bolt frozen to shaft
The 1/4 inch impeller bolt to shaft would not budge with a nut driver so I had to use a ratchet to loosen it. I could not hold the drain impeller with an adjustable wrench so I had to use a vice-grip. This still did not loosen it so I used an oscillating power saw to cut away at the bottom of the drain impeller being careful to only cut so deep, I didn't want to cut into the motor shaft. Once I had cut some grooves into the drain impeller, I could break it into pieces and remove it. Upon reassembly I tightened the 1/4 inch bolt with the ratchet.
Parts Used:
-
Elmer from YORKVILLE, IL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Not dispensing detergent
Followed instructions as the videos on this page show.
Parts Used:
-
Mandy from GREENWOOD, SC
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
DOOR leaking
door gasket old the vent was pluged up full of black slime cleaned out and door stopped leaking
Parts Used:
-
mike from SHELTON, WA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
3 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
cut wire in center sprayer to remove plastic holder for new basket
-
JOHN from IONIA, MI
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cap was missing/lost.
-
Jose from Coolidge, AZ
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Top glass rack broke
Just watched the YouTube video they recommended watching and it is very helpful. No tools needed and was finished in several minutes.
Parts Used:
-
James from MILFORD, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dish washer leaking out bottom of door
New gasket did not fix problem. Cleaned air vent cover for steam to exit. Gasket not the problem but new one looks good. thank you
Parts Used:
-
Ed from Ulysses, KS
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer arm wound rotate, bearing was worn.
required NO tools,
just unscrew the large thumb screw, and replace the washer arm bearing!
problem solved like that!
maybe a 5 min job. part was a perfect match.
just unscrew the large thumb screw, and replace the washer arm bearing!
problem solved like that!
maybe a 5 min job. part was a perfect match.
Parts Used:
-
james from encinitas, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
just slipped yhr olf part out and replaced it w/the new part
-
C BURRDYNE from ORANGEVALE, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
3 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door leaking water.
The old gasket around the door pulled out easily but was pretty nasty. While cleaning the channel out, kept finding more gunk that had built up. I decided to go ahead and take off the Inner Door. Used Torx driver to take off the screws. Found a tremendous amount of gunk built up. Was well worth taking the extra time to clean it all out. Replaced the Inner Door and put new gasket in channel. No more leaking!
Parts Used:
-
Jonathan from Henderson, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
3 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!