All Installation Instructions for Whirlpool Dishwasher DU900PCDZ2

original dishrack had become rusty

installed a new rack

Parts Used:

Lower Dishrack Kit

Tom from Peoria, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

leaking around door

After cleaning the filter located on top left of door(used a screw driver to pry out) and following the install gasket video problem solved.

Parts Used:

Dishwasher Door Gasket - Gray

Curtis from Enderlin, ND
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Dirty Dishes

Nozzle cap rubber housing was split and cracked. It simply unscrews. The replacement was a matter of screwing the new nozzle cap on. My wife was trusted with this installation. Believe me, this indicates how easy it was.

Parts Used:

Nozzle Cap

George from New Freedom, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

lower rack started to rust through coating

Since there were no printed instructions, we looked at the photo schematic.
Reassembly using the photo was easy by putting the old rack alongside the new one and adjusting the new rack spacing to match the old one.
We also had new wheels which snapped on.
We were delighted to repair and replace this good, older dishwasher rather than purchase a new one!

Parts Used:

Lower Dishrack Kit

Carol from St Johnsbury, VT
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

One door spring broken, replaced both

As described with instructions, removed original "bearing," installed replacement, removed original spring, installed replacement springs. Not difficult.

Parts Used:

Heavy Duty Spring Kit

Donal from SPRINGVILLE, TN
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

THE LOWER RACK WAS CORRODING IN SPOTS AND WAS RUSTING

THERE WERE NO INSTRUCTIONS INCLUDED, COULDN'T FIGURE 0UT HOW TO INSTALL THE NEW ROLLERS ON THE NEW RACK FINALLY INSTALLED THE OLD ROLLERS ON THE NEW RACK AND THEY WERE MUCH EASIER TO INSTALL I DONT UNDERSTAND
WHY THE NEW ROLLERS WERE THE SAME AS THE OLD ROLLERS
EXCEPT FOR THE COST.

Parts Used:

Lower Dishrack Kit

JOHN from JUPITER, FL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

throwed water out under the door

Did not use the new parts. After removing the spray arm, found a screw out of place. Put the seal ring back in place and the screw back in the hole. Machine works like new.

Parts Used:

Dishwasher Pump Outlet Seal

B Jean from MONTPELIER, OH
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

my old lower dishwasher rack was rusted out and some parts broken.

Snapped on the rollers, removed the center part from the old rack that sprays the water and snapped it on the new one. We then bent the back row down so it would acomodate my larger items. My old rack had that feature. You could either have the rack up or down. Now l
ooks beautiful and works perfectly.
Could have used some directions though.

Parts Used:

Lower Dishrack Kit

Kathy from ELGIN, IL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

i had a leak under the dishwasher when the pump turned on.

I replaced the seals per the video instructions.

Parts Used:

Drain and Wash Impeller Kit

Walter from KINGSPORT, TN
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)

1 person found this instruction helpful.

Was this instruction helpful to you?

Lack of assembly instructions

YouTube was very helpful
New racks works better that way expected. Rearrange ment maximized loading

Parts Used:

Dishrack - Rack Only

Lower Dishrack Kit

Ray from Lufkin, TX
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Dishwasher would not dispense soap

Both springs (8066018 and 3368999) were replaced as recommended in your troubleshooting guide, but did not resolve the problem. Finally the Dual Motor, 3374501, was replaced. During the above, the plastic face of the door fell off, which created a nuisance task before proceeding to fix the original problem. However, while replacing the motor, I realized the purpose of the two, T-shaped studs sticking out of the motor. It is absolutely necessary that these sit inside the slots which engages the sliding plastic cover, which is spring loaded, in order to engage the release of the soap dispenser door. It was truly a learning experience, but I got it done.

Parts Used: