DU8900XT0 Whirlpool Dishwasher - Instructions

This job took 30 seconds to accomplish. The old wheel assemblies (4) just snapped off and the new wheel rollers just snapped in their place. No tools were needed. Extremely satisfied with this product. Wished I had performed this repair years ago!

I simply snapped off the old broken roller set and snapped on the replacements. No tools were even needed and now the rack rolls smoothly on all wheels! This has encouraged me to try other
repair projects.

The lower dish rack rolls directly out of the dishwasher without problem - there is no permanent attachment. The new rack comes as a kit, which includes the 4 required dish rack wheels (Part # 6 in the diagram). One part (only) from the original dish rack needs to be removed and re-installed on the new rack - the upper spray arm tower (Part #5 in the diagram). That is easily removed from the original rack with a 1/8 counterclockwise turn, to disengage the 'feet', and installed on the new rack with a 1/8 clockwise turn. The kit is designed to allow for use on multiple models, so there are 'extra' parts left over, after it is used for the DU8500XX-2 dishwasher. These can be discarded.

Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.

Took the old one off and replaced it with the new one we received from you. It was great because we received the part just in time to do the Thanksgiving dishes! Thanks PartSelect.

Replaced Seal and Seal Frame worked real good

Replaced broken door spring and retainer:
1.To gain access - removed two retaining screws in lower front panel below the door. Lifted panel off hooks in toeplate.
2.Replace spring and retainer - note how retainer fits into spring and how spring is attached to door hinge. Rehook spring and retainer in same slot as before. There are two springs. If only one is broken, let the unbroken spring be your guide in replacing the new one.

Since there were no printed instructions, we looked at the photo schematic.
Reassembly using the photo was easy by putting the old rack alongside the new one and adjusting the new rack spacing to match the old one.
We also had new wheels which snapped on.
We were delighted to repair and replace this good, older dishwasher rather than purchase a new one!

the design of the new roller kit was a little different than the original. took a minute to figure the installation. all went well. the new roller assembly fit the 30 year old dish rack

THERE WERE NO INSTRUCTIONS INCLUDED, COULDN'T FIGURE 0UT HOW TO INSTALL THE NEW ROLLERS ON THE NEW RACK FINALLY INSTALLED THE OLD ROLLERS ON THE NEW RACK AND THEY WERE MUCH EASIER TO INSTALL I DONT UNDERSTAND
WHY THE NEW ROLLERS WERE THE SAME AS THE OLD ROLLERS
EXCEPT FOR THE COST.

Did not use the new parts. After removing the spray arm, found a screw out of place. Put the seal ring back in place and the screw back in the hole. Machine works like new.

I searched for the 18x5x5 insulation.,ordered it from Part Select. Waited. Company sent wrong part. Called, they gave me a refund, reordered, promised 2 day free shipping. Waited more than a week, paid for 2 day shipping. Received same, wrong part. Still don't have repair done. Looking elsewhere for part.

when removing all the screws from the door gasket the dishwasher door and frame separates making reassembly not possible. you have to leave at least one screw on bottom half on each side, After all that the door would not close. I had to remove the new gasket and put the old one back on.
I need to return the gasket for credit

YouTube was very helpful
New racks works better that way expected. Rearrange ment maximized loading

I replaced the seals per the video instructions.