DU8570XT0 Whirlpool Dishwasher - Instructions

I looked in the bottom of the dishwasher after browsing the website regarding possible solutions. When I removed the bottom spray arm I noticed three screws missing from the pump housing. The loose pump outlet had allowed the seal to push out. Ordered-Normal shipping on the part.

Unsnapped the old rollers and snapped in the new ones. Worked great and easy. I was very pleased that the parts came so soon as well. Thank You, Ms. Cason

1. Turn off the electrical switch that powers the dishwasher. 2. Open the door of the dishwasher and find the two phillips head screws that secure the top of the dishwasher to the kitchen counter. 3. Remove the screws. 4. Gently move the machine side-by-side a bit while pulling it out onto the kitchen tile (be careful, the water-supply hose, electric cord, and dishwasher drain hose may not be long enough to allow you to pull it out very far - don't break or kink the hoses). 5. Remove (pull off) the black plastic fastener located on the bottom/rear of each side of the dishwasher. 6. Remove the old surround. 7. Lay the new wrap in place and secure with the two plastic fasteners. 8. Push back into place, secure the two screws, check your hoses.

Used the diagram and disassembled and reassembled.Used most parts that were in kit as it also fit other models and did not need all the parts.

Received new rollers promptly as ordered. Removed the old ones by snapping them off and simply snapped the new ones on. Took less than 5 minutes and job was a complete success. Wife happy and I am safe for now

took off the old wheels and put on the new.couldn't be easier.

Old tandem rack for rollers popped off lower rack by applying a small amount of pressure. New tandem rack rollers look slightly different, but pop right in place. By replacing all four tandem rack rollers the lower rack glides smoothly in and out of the dishwasher. Entire replacement can be done without tools, by hand in less than fifteen minutes.

The repair was simplicity itself. Remover the sprayer arm, removed the torx screws, replaced the seal, and reversed the process of disassembly. When I found out where the dishwasher was leaking from, I called KitchedAid and was ready to replace the overflow float. The part was 42.00 and wouldn't have fixed the problem. When I found this web site and read other peoples experience, I checked the pump seal, and it was obvious that it had blown out. That saved me a Loy of time and money.

I removed the rack and then pushed down on the old rollers to remove them from the rack. I then installed the new rollers in the same location.

My husband took the dishwasher apart three times, it was a little frustrating, but was worth the $50 part because it made his wife, very, very happy! A dishwasher operating is on the top 5 list of favorite electronic items in our house.

I ordered the parts on Fri. and they came on Sat. Thanks. I had to pull the dishwasher forward about 6". Then just put the springs on. They don't have much tension with the door closed. Easy. Thanks again.

Replacing the cup latch and dispenser cover was pretty easy. First, I removed the inside cover of the door of the dishwasher. Then I carefully removed the plastic covers/slides on the door, removed the broken cup latch and then inserted the new one. Replaced the plastic covers/slides, the reinstalled the inside cover on the dishwasher. Next, I removed the dispenser cover and installed the new one. It snaps off/on, by the way. It only looks like it slides on/off.

I tried going online to get some diagnostic help and never found a site that had a step by step help plan. I then did a little reading on different sites, to eliminate and perhaps diagnose my problem I use epoxy to glue the impeller(which spun freely) to the screw and it held long enough for me to see how it worked. I surfed sites to find the least expensive drain and wash impeller kit. One site had a cheaper price but I chose Parts Select because of the shipping so the end result was the best results for me. I am not sure but the estimated time was 1.7 or 1.8 days delivery that I did not believe would happen. When I received the parts and did the repair my final time from ordering was less than a day and a half. I could not have done the job myself without the video because the parts were very different. My biggest obstacle, other than my ignorance, was some sort of chemical on the screw that would not allow me to loosen it. I used a dremel to cut the head off and then a torch to heat the stub so I could remove it. After I received the kit I saw a chemical on the screw threads so online research told me heat loosens the chemical. My dishwasher is around 25 years old,I have worked on it three times now and replacing the impeller was the most difficult task to date. Should it last and develop another problem I will go to parts select first and start my quest.

Replaced the lower seal, drain impeller,chopper blade, and wash impeller. Problem is still not solved but the inner parts have been replaced. Only thing logical next is the check valve. Unit cycles well and if I turn the dial to just before the rinse cycle and watch, I do see water draining from the unit...Of course while replacing these parts, I checked other things and found a loose spring behind the front cover. It can be seen on the diagram as it is part of the detergent door mechanism (or so I believe), but it is not clear on where the spring actually connects to.

The repair was fairly simple and made easier with an installation video. The repair went well and there's no more leak.