DU800CWDQ2 Whirlpool Dishwasher - Instructions

The hardest part was locating the leak. After consulting the other repair suggestions, I concluded that the gasket was a little more worn on one side than the other so I ordered the gasket. The evening before the gasket arrived (quick delivery from partselect.com) I decided to shim out the old gasket with some old door insulation. It made the door harder to close but it didn't leak any more. When the gasket arrived I replaced the old with the new. It leaked more than ever. After reading more repair instructions, I decided to take apart the door vent and check it. It was packed solid with gunk. After a good cleaning, I put everything back together. No leaks! I tried every repair listed except the door vent. Guess steam is a good gunk conduit LOL. I supposed I didn't really need the new door gasket but I can tell the door has a tighter seal now. Here's a tip to watch for. If the door doesn't leak right away after the washer starts, take the door apart and look at the vent. It can look just fine from the outside and that's deceiving. Someone else mentioned the 'leak' timing that finally got my attention and lead to the 'fix.'

Started down Parts Select list of possibilities. Replaced the door gasket (1/2 hour), still leaked. Replaced water deflectors (15 min), still leaked. Was looking at steam vent and read the repair submitted by "mary from Fountain Green UT". Removed and thoroughly cleaned the steam vent (1/2 hour). Stopped leaking and is working fine now. Repairs were very easy using Parts Select instructions.

Turned off power to dishwasher. Removed inner door panel. Cut wires as directed and installed new switches. Also installed new spring on soap door opener. Reassembled, ran and tested. Take your time, this repair is pretty simple.

Safety First: 1) I shut power off to dishwasher, 2) Shut water off to dishwasher, 3) Checked electrical with tic tracer to confirm power was off after removing bottom dishwasher panel, 4) I checked the orientation of old valve: connection plate, water inlet tubing, hose connection, and electrical connection. Then I removed the 2-screws that held the valve in place with a nut driver. Next I removed the compression clamp from the rubber hose with pliers and a screw driver. Then I removed the compression fitting and copper tubing from the old valve. Note: Kenmore used a compression fitting to connect the copper tubing to the original water valve. That said, I had to remove the old fitting and install a new one (using a pipe cutter on the copper tubing before installing a new compression fitting). I also bought a new valve elbow because the old one was not serviceable. With all three connections made up (the rubber tubing connected to the new valve along with the electrical connection, and the new elbow and compression fitting installed) I tested for leaks and reconnected the holding bracket to the side of the dishwasher frame. Before calling it good I vacuumed out the area under the dishwasher. Note: because the water inlet valve is located close to the floor, all the work had to be done while laying on the floor...awkward. This too, I had to purchase a new valve elbow and compression fitting so halfway through the project I had to make a run to the hardware store. Overall, replacing the water inlet valve on a 10 year old Kenmore dishwasher is an easy project...pretty straight forward but having to go to the hardware store stretched the installation time out to over an hour.

I read everyone else's fixes, which were very helpful but my solution of removing the plastic from the motor shaft was a lot easier than others. I simply used side cutters and made two cuts into that plastic piece and it Fell of. much easier than the person using several Dremmel blades to cut it off.. That was the most difficult phase until I grabbed my ole phone company side cuts and just cut it off in 15 seconds. Thanks for all the other tips. I love dealing with Parts Select, Fast and efficient. Jim W

Unplug dishwasher from electrical, water supply and drain hose. Pull dishwasher out from under cabinet. Unscrew water whirler from inside washer, then remove motor. Remove black boot from motor. Unscrew keeper from impellor housing. And you are there! Pull impellor off motor shaft. Replace seal first, then replace impellor. So easy this girl did it. But, this girl also does small engine repair!

Remove lower rack in dishwasher, remove dishwasher, lay dishwasher on it's back, remove and replace motor and pump.Install new impellar with new seal. reconnect water, electrical and drain hose. Easy Peasy

I replaced the seal, still leaked. Once I noticed that it was only leaking from the left side, we did a Google search to find that the screen in the upper left of the door could be the issue, causing back pressure. Once the screen was cleaned, no more leaks.

took out old door gasket replaced it with new, also cleaned the air vent at top of door. Ordered shield at same time but didn't use it, so returned it, haven't received refund yet, but expect one soon. Dishwasher works great and NO leaks. Wonderful website

Removed dispenser cover by using flat screwdriver, then slid the lid hinge pin and lid spring by pushing the lid hinge pin out on the silverware trade side. Then I put the lid hinge pin back into its place, once started I put the lid hinge spring on the lid hinge pin and pushed the pin into place, used flat screwdriver to put the lid spring in place, then I snapped the soap dispenser cover on the lid hinge pin. It took me about 5 minutes to remove and replace these parts, a very easy repair.

slid the pin into place, noting correct position of spring, backed hinge pieces with screwdriver and pressed door into place. Your video made it easier than ever. ( My 2nd time replacing the pin. ) Great repair experience.

The repair man from a serve we use, look up on how to replace the door gasket. Washing hands, do not stretch, and tap rubber into place. No more leaks.

This was stupidly easy! I found Parts Select from a Google search on making the repair. That took me to a YouTube video that Parts Select had posted on how to repair. I followed the instructions and it was fixed in 10 minutes and that was only because I took my time. I ordered the part online from a link on YouTube and I had it in two days............. Unbelievable!!!!

I paid a repairman over $100 to tell me he could find nothing wrong with my leaking dishwasher (it didn't leak when he ran it). I narrowed down the problem to a missing water deflector, but decided to replace the door gasket as well. It took less than 5 minutes to do the job. The only tool I used was a pair of needle-nose pliers to grasp the old door gasket and get it coming out of the groove. Thanks PARTSELECT for super-fast shipping and a website that is easy to navigate. I'll be coming back, 'cause all of my appliances are getting some age on them!

Just followed the online instructions. I used white vinegar to clean any residue first. So easy.