DU800CWDQ2 Whirlpool Dishwasher - Instructions

I removed the three screws holding the motor on the housing. Then I took the two hoses off and from inside the washer I unscrewed the ring at the base of the wand that holds the housing in place and removed it. I then replaced the impeller and seals and reversed the process to put it back together. Cost me 26.00 for parts and shipping. I couldnt imagine what anyone else would have charged. I will do business with PartsSelect again in the future.

We read your help site and was able to find what was causing our water filling probelms. Order the valve intake part and made the repair and the dishwasher works like new. You saved us a repair bill from the professionals and they couldn,t done a better job. I will recommand to site to everyone. Thanks Again

After getting the pump and motor off of the dishwasher, I used a screwdriver and small hammer to break the impeller off of the motor shaft. The shaft was corroded and pitted real bad but this doesn't matter because the shaft of the impeller actually goes through the seal. I removed the old seal and replaced it, slipped the new impeller back on the motor shaft and put the pump and motor back on the dishwasher. Our local repair man told us it couldn't be repaired and we needed a new dishwasher. I had the parts from Part Select in 2 days. The parts were less than $35 dollars and repair very simple. The person on your comment section on how to fix it that said to break the old impeller off of the shaft made the job very simple.

the plastic pin that retains the spring has a head on one end that hits a plastic stop on the door to keep it from coming out. I used a small grinder and made a flat spot on the head diameter to make it easy to slide out. This is easier than trying to pry the door off the pin at the two retaing snaps. I was conderned these pin retainer clips were brittle and would break off.
Once the pin is slid out, it is a matter to hold the new spring holes in line with the pin. rotate pin so flat side you ground is turned up, so pin will not move out that way. Tiij about an hour

Swapped out the old upper dish rack with a new one. A video made the change simple.

The door seal was easy. In less than 15 minutes I peeled the old one off and installed the new one. Also the new seal arrived in 2 days. In replacing the seal I noticed a screw laying in the bottom of the dishwasher. As I removed the lower washing arm which was real easy I noticed that the plastic bearing for the lower arm was no good. Late Thursday evening I went on line and ordered the bearing, and to my surprise it was delivered to my house on Saturday. In 15 minutes I had the bearing installed and we were back in business. I'm just amazed at how easy your web site is to use, and the promptness of the parts delivery. You guys are great.

I grabbed the lower right end of the gasket with my Leatherman Tool pliers and pulled out the old gasket.
I installed the new gasket. No cleaning was necessary.
It took less than five minutes. It now works like new.
I ordered the part with standard delivery and it was here in just a couple of days. Very easy fix.

Pulled out the old with needle nose pliers. Pushed in new door seal with fingers.

Removed and replaced leaking water inlet valve, 10 minutes and saved me a hundred in plumber fees.

The whole job took less than 5 minutes...no tools were needed The diagnosis was right on the money

Just screwed the new cap in. This PartSelect was AWESOME. So easy. Lighting fast shipping !!!!

Snap the old lid off, remove the pin & spring & install new Pin & Spring. Very easy. Thanks To Parts Select got the right parts.

Took less than 5 minutes. Pried edge of old door seal out with a flathead screwdriver, then slowly pulled out old seal. Thoroughly cleaned area for new seal with rubbing alcohol, inserted new seal and trimmed the end to fit just right. Presto, no leaks whatsoever!

Took off bottom plate (2 screws) and ran unit to ensure where leak is from....it appears to be the door seal. Pulled out old seal with fingers and replaced door seal, ensuring its properly "fitted"..ran unit, no leaks, put bottom plate back on

removed old seal, placed new seal in place. Used my fingers to push it in place. It didn't work as it still leaks. I've put vaseline on the seal and door and it helps but still leaks. The dishwasher doesn't overfill, so I still have the problem, just not as bad.