DU2000XS0 Whirlpool Dishwasher - Instructions

Turn off the breaker to the dishwasher - there will be water very near the motor and other electrical components. I first scooped and towelled all the water out of the bottom of the dishwasher. The drain valve can be accessed from the bottom front of the dishwasher without pulling the unit out from under the counter. There were 4 screws to remove the 2 bottom metal panels. Next use pliers to loosen and slide back the hose clamp connected to the drain. Have a towel ready and pull the drain hose off the white check valve. The check valve can then be removed by unscrewing it - you may need to use pliers. Put the new one on and everything back together.

Put on new door, making sure the spring was set to flip the detergent door open in order for the detergent to properly do the dishes

took off the old wheels and put on the new.couldn't be easier.

Old tandem rack for rollers popped off lower rack by applying a small amount of pressure. New tandem rack rollers look slightly different, but pop right in place. By replacing all four tandem rack rollers the lower rack glides smoothly in and out of the dishwasher. Entire replacement can be done without tools, by hand in less than fifteen minutes.

Received new rollers promptly as ordered. Removed the old ones by snapping them off and simply snapped the new ones on. Took less than 5 minutes and job was a complete success. Wife happy and I am safe for now

Unsnapped the old rollers and snapped in the new ones. Worked great and easy. I was very pleased that the parts came so soon as well. Thank You, Ms. Cason

Turned off water and power. Used small nut diver to remove two upper screws from kick-plate, and loosen two screws in lower key slot of kick- plate. Removed kick- plate. Used plier to compress snap ring and remove hose to washer. Pulled off electrical connector. Used 5/6 wrench to remove copper water inlet. Used nut driver to remove two screws holding old valve. Once out removed the water connecting elbow from the old valve and installed it on the new valve. Reversed process to reinstall. Didn't even have to remove washer from the counter. My 25 year old washer is working like new again.

I simply looked at the remaining spring to see which notch it needed to be attached to. I went in very well using a long needle nose plier. Works great.

I removed the rack and then pushed down on the old rollers to remove them from the rack. I then installed the new rollers in the same location.

Removed cover and broken spring ,installed new spring and cover.Did it all in less than 10 minutes

screw it in then hook up the hose.

Very easy. Slide the dishwasher out a few inches, install spring per the good instructions, and slide the dishwasher back. Service was amazing. Part arrived just over 24 hours after I made the on-line order. I will use Part Select for all my future appliance parts needs.

popped off the old rollers + tracks; then snapped on the new ones; as my granddaughter would say "easy peasy lemon squeezy". Took hardly any time at all. :-)

A VERY easy repair! I simply pried off the old wheel assemblies with a screw driver and popped on the new ones. I was a little concerned about the new ones fitting correctly as the dishwasher is over 25 years old, but after a week they still work fine. An easy fix to an annoying problem....wish I had ordered these ages ago! Bottom rack of my dishwasher now rolls in and out like new (instead of the the few remaining wheels constantly falling off!) Very happy I ordered these and delivery was quick.

My soap dispenser latch was coated in grit, the gasket was deteriorated, and the spring was barely strong enough to open the door, so the door didn't always latch closed or open when it should. I followed the video and everything went exactly as shown. Once the liner was removed, I discovered the back (including the latch mechanism) was covered in soap residue and other gunk. I hosed it off on the backyard and resumed the repair. The dispenser now latches easily and opens with a convincing SNAP. I wouldn't have known how to replace the latch without the video. Great website!