DTL18ICSJRBS General Electric Refrigerator - Instructions

Removed shelf by pushing to left and lifting up on RH end. Removed screws in plastic cooling tower and slid tower up. Pulled back wall of freezer compartment out, RH side first. Removed two screws from fan bracket, unplugged fan wiring harness by compressing connector spring clips and pulling joint apart. Pulled fan blade off (note location of blade on shaft for reinstall alignment purposes), removed both green grommets.Then just reinstalled new items.My philosphy on repairs of this nature is to replace all related parts that could be contributing to problem. The parts are cheap compared to the aggravation and inconvenience of doing the repair several times until you fix the problem. You don't need to purchase the compression ring if you buy the fan blade as it has one already installed on it. Problem solved, though now that the noise is gone am hearing fainter similar noises from lower fan. Should I be surprised, both fans are of similar design.

Removed the ice maker from the freezer. Removed the switch. Tested the switch with a multimeter. Ordered a new switch. Replaced it in the box. Installed the ice maker ( 3screws and electric cord plug. It works. Details available on the internet.

I took the advice off of your website about the only thing that will fix
the problem is change the run capacitor. I felt assured that I would
have a working refrigerator freezer after making this change. I was
pretty disheartened when it didn`t solve anything. I was not going to
take the new part back out after the small challenge of putting it in.
The next day I found out how to test the old capacitor and it was still
good. I will just have to eat the $49. I did learn not to take advice from
a website even if it seems like a sure thing

The part i received fit perfect, i just removed the old part and put the new part in with the screw driver.Really easy

turned off water supply, took screws out of bracket, then unhooked water lines. Installed water lines onto new valve, plugged it in then screwed bracket back onto fridge, turned on water and was back operating

I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.

Instructions say run capacitor is by motor, but on this frige its in the refrigerator compartment. The capacitors looks different, one square and the other long

Ordered the icemaker replacement. unplugged the unit, followed the simple instructions and got it done in less than 30 minutes. It did take a LONG time to start making ice. But it's working now.

Repair was very simple. Removed refridgerator bottom back panel, about 6 or 7 screws. disconnected bad valve, installed new valve , connected water supply line and then reinstalled panel. Took about 15 minutes from start to finish.

I removed the broken frame, glass, and bins from the refrigerator, cleaned the area, put the new frame in place making sure it was fitted into the brackets securely, and replaced the glass and bins into their proper slots.

First I removed the left condensor fan motor bracket nut, loosened the right motor bracket, dropped the moter bracket down freeing the motor from the rubber grommets.
Pulled the fan off from the motor shaft, pressed the new fan on the shaft and installed new grommets. Replaced the motor bracket and tightened the right bracket nut and checked fan for clearance and free spin. Reinstaled the left bracket nut. Turned on the refrigerator and checked fan for action. Everything worked great.
I did not know the fan replacement came with a compression ring already installed, so now I have an extra compression ring.

I ordered the wrong part, the ice maker assembly, because your diagram was not marked properly. I returned the part and you credited my account. Thanks. Ordered the new bucket. It worked fine. Now I have ice and crushed Ice whenever I want. Thanks.

p.s. I didnt use any tools, but to satisfy you I select nut driver.

First I had to go to the hardware store to buy a star bit to remove the old screws ($1.09). I attached it to my quarter-inch drill and used it to remove the old screws. I then used those same screws to attach the new slide. Once I had the star bit, it was little more than a five-minute task.

Was concerned that new icemaker was quite a bit different than the one we were replacing. Called GE to confirm it was correct.

Went ahead and installed the unit, using the supplied electric cable adapter.

A little difficult to deal with the extra cable, but everything worked OK and it's making ice normally.

The replacement single outlet water valve was not an exact replacement and required a slightly different mounting position. The original plastic hose to the ice maker attached to the valve with a plastic nut. The new connection requires only pushing the hose into a hole in the valve. Easy and simple. However, the new mounting angle promptly broke the brittle old plastic hose. I was able to pick the broken pieces of hose out of the valve with a fine point pick saving the new valve. If I hadn't been able to pick the broken pieces out of the new valve I would have had to order another one. Off to the big box store to buy new 1/4 inch plastic hose and a coupler. Repair completed and no leaks. If the hose hadn't broken, the I would have been done in 15 minutes. I suggest you plan to replace the entire plastic hose when you replace the valve.