DP940PWSQ0 Whirlpool Dishwasher - Instructions

Pulled off the bottom trim, slid the old panel off and put the new panel on. Then popped back on the bottom trim.

Replaced door gasget took 5 minutes tops. Ran cycle and still had leak. Called local repair person. After thoroughly checking out the dishwasher and running soapless cycle determined problem to be soap build up over time. He ran a commercial cleaner through a complete pots and pan cycle. No more suds and no more leak repair complete. Did not actually need door gagset but it was super easy to change and delivery service was great.

The parts you sent fit perfectly and went in effortlessly. You would not believe the time effort and supper glue I used trying to repair the unit without getting new parts.

THIS WAS A GREAT SUCESS.

I used the screwdriver to pry the old lid off of the horizontal pin upon which it rotates. One must be careful before removing the old lid to note how the return spring is deployed. The short legs on the spring must be in the lip of the lid before you snap the new lid onto the horizontal pin. It was helpful to lubricate the two catches on the lid that snap on the pin with some liquid soap before attempting to snap them on the pin. After the lid is snapped into place and the short legs of the coil spring are in the lip of the lid, use needle nose pliers to attach the other end of the coil spring to the pillar where it was before you removed the old lid. There are videos showing how to do this on Youtube. The spring part is a little tricky. The video makes it look a bit easier than it is..

First I read the other repair stories and knew it was a relatively easy repair. I removed the end caps on the front of the top dish rack and removed it for ease of access to the part. I then removed the two screws holding in the old part observing how it was positioned to make sure the new part was replaced in the same manner. I put the new part in place and screwed in place and replaced the dish rack. Everything is working just fine.

1st i removed the broken threds with a wood chisel (just got a chisel that fit snug in the hole , tilted it a little and turned out the threds)
after looking at the print that was on the web sight i put the parts back on the same way. note::: i was instucted by my wife not to help with the dishes ever again . i had put two spoons ,a fork and a knife in the wrong rack ...silverware will tear up the dishwasher.....

remove star screws holding inside door panel. remove plastic cover that protects latch assembly. hook one end of spring on stationary pin on inside of slider bar. Hook other end of spring on pin on slider bar. replace cover and door panel.

Actually I ordered the drain and wash impeller kit because it was listed as the #1 cause of failure to drain. I then hired a plumber to install it. He did so and that didn't solve the problem. So I was about to buy a new dishwasher. I then noticed that the second most frequent cause was a problem with the "dishwasher drain check valve." I watched the "partselect" video on how to change that. I didn't have a new one but I thought I would take out the part and see what I could learn. As it turned out it was blocked by a little piece of what appeared to be a walnut chip. I cleaned it out reinstalled the drain check valve and the problem was solved.

Installed pump kit. Was surprised the kit seemed different( some parts changed or deleted. Instructed to discard old parts and follow with new configuration. Reassembled and tried t fin it works fine now. Thank you so much

I watched the video link sent in an email and followed exactly what they did in the video. I removed the star head screws holding the door liner in place. Then removed the protective cover on the inside. I disengaged the component holding the latch in place. I replace the component that holds the latch in place and then snapped the new latch in place. I turned the dishwasher dial until the prongs were fully retracted. I replace the protective cover and then put the door cover back in place. I initially only placed the left bottom star head screw until I was sure that the latch was going to release. I tested that it was working properly by slowly turning the dial on the dishwasher control. Once I knew it was working I replaced the rest of the screws.

Took old one off , installed new one!!

1 Screw 5 minutes thanks for the quick service will definitely use ya'll next time

Got the new door and tried to put it on. The door went on very easily. However, there's a spring that opens the door when the main wash cycle comes around. I never did get that spring right. None of the drawings showed the correct position and after an hour of trying to get it to work right, I gave up. The door comes open slightly (but not because of the spring) when it's time, and the liquid soap runs out due to gravity. But I wouldn't try to use soap powder because the door doesn't come open far enough.

removed old check valve from bottom of dishwasher and replaced with new one. I used channel locks to do this, disconnect hoses and screw out check valve, and put back in opposite order, make sure the dishwasher is empty of water or have a plastic bowl or such to catch water. Take off two front covers on bottom of dishwasher to access check valve ,white with hose attached.

Removed the washer from the cabinet, although the repair kit could have been replaced without this step. However, it still made it easier. Removed the spray arm assembly and the top cover to the motor. I had to block the motor to keep it from turning while I unscrewed part number 11. The rest was very self explanatory. The "impeller" was seized onto the motor shaft (20 years old) so I had to use a chisel to break what remained off, then clean some corrosion from the shaft. The repair kit worked and the pictorial parts diagram that came with the kit was very clear. Bottom line: "Easy peasy, lemon squeezy!" Great web site for diagnosis and parts diagrams!